WISECOM, INC.

WS-2814JS6 (INTERNAL)

Card Type

Modem (synchronous/asynchronous)

Chipset

Sierra

I/O Options

Voice, microphone in, speaker out

Maximum Data Rate

28.8Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

8/16-bit ISA

Fax Class

Class I & II

Data Modulation

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34

Fax Modulation

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

CONNECTIONS

Function

Label

Function

Label

Telephone line in

CN1

Speaker out

CN3

Telephone line out

CN2

Microphone in

CN4

INTERRUPT SELECTION

Setting

JP6/A

JP6/B

JP6/C

JP6/D

JP6/E

JP6/F

í IRQ3

Open

Open

Open

Open

Open

Closed

IRQ4

Open

Open

Open

Open

Closed

Open

IRQ5

Open

Open

Open

Closed

Open

Open

IRQ10

Open

Open

Closed

Open

Open

Open

IRQ11

Open

Closed

Open

Open

Open

Open

IRQ12

Closed

Open

Open

Open

Open

Open

SERIAL PORT ADDRESS SELECTION

Setting

JP6/G

JP6/H

3F8h (COM1:)

Open

Open

2F8h (COM2:)

Open

Closed

3E8h (COM3:)

Closed

Open

í 2E8h (COM4:)

Closed

Closed

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, H, L, M, O, P, Q, T, V, X, Y, Z

&C, &D, &F, &M, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\C, \G, \N, \Q, \V, \X

%A, %C, %D, %Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S18, S25, S26, S38

Note: See MHI documentation for complete information.

Proprietary AT Command Set

AUTO-FALL FORWARD/FALLBACK

Type:

Configuration

Format:

AT [cmds] &An [cmds]

Description:

Selects whether the modem will automatically fall forward or back in response to line conditions.

Command

Function

&A0

Auto-fall forward/fallback disabled.

&A1

Auto-fall forward/fallback enabled.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested about the modem.

Command

Function

I0

Reports product identification code.

I1

Reports ROM checksum.

I2

Tests and reports ROM checksum.

I3

Reports firmware revision and model ID.

I4

Reports configuration ID.

LOCAL SERIAL PORT SPEED

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Description:

Sets the speed of the local serial port.

Command

Function

\T0

Auto-detect serial port speed.

\T1

Use speed of last command.

\T2

Set speed to 300bps.

\T3

Set speed to 1200bps.

\T4

Set speed to 2400bps.

\T5

Set speed to 4800bps.

\T6

Set speed to 7200bps.

\T7

Set speed to 9600bps.

\T8

Set speed to 12Kbps.

\T9

Set speed to 14.4Kbps.

\T10

Set speed to 16.8Kbps.

\T11

Set speed to 19.2Kbps.

\T12

Set speed to 21.6Kbps.

\T13

Set speed to 24Kbps.

\T14

Set speed to 26.4Kbps.

\T15

Set speed to 28.8Kbps.

\T16

Set speed to 38.4Kbps.

\T17

Set speed to 57.6Kbps.

\T18

Set speed to 76.8Kbps.

\T19

Set speed to 115.2Kbps.

\T20

Set speed to 128Kbps.

PROTOCOL

Type:

Configuration

Format:

AT [cmds] &Hn [cmds]

Description:

Selects the modulation protocol that the modem will use.

Command

Function

&H0

Use V.34 with fallback to lower protocols.

&H1

Use V.34 only.

&H2

Use V.32bis with fallback to lower protocols.

&H3

Use V.32bis only.

&H4

Use V.32 with fallback to lower protocols.

&H5

Use V.32 only.

&H6

Use V.22bis only.

&H7

Use V.22 only.

&H8

Use Bell 212A only.

&H9

Use Bell 103A only.

&H10

Use V.21 only.

TRELLIS CODING

Type:

Configuration

Format:

AT [cmds] &Un [cmds]

Description:

Selects whether the modem will use trellis coding.

Command

Function

í &U0

Trellis coding enabled.

&U1

Trellis coding disabled.