PUREDATA, LTD.

SATISFAXTION MODEM/100

Modem Type

Data (asynchronous)/Fax

Maximum Data Rate

2400bps

Maximum Fax Rate

9600bps

Data Bus

8-bit ISA

Fax Class

Class I

Data Modulation Protocol

Bell 103A/212A

ITU-T V.22, V.22bis

Fax Modulation Protocol

ITU-T V.27ter, V.29

CONNECTIONS

Purpose

Location

Purpose

Location

Line out

CN1

Line in

CN2

BASE I/O ADDRESS SELECTION

Port

SW1/A

SW1/B

COM1: (3F8h)

On

On

» COM2: (2F8h)

Off

On

COM3: (3E8h)

On

Off

COM4: (2E8h)

Off

Off

INTERRUPT SELECTION

IRQ

SW1/C

SW1/D

SW1/E

SW1/F

2

On

Off

Off

Off

» 3

Off

On

Off

Off

4

Off

Off

On

Off

5

Off

Off

Off

On

Proprietary AT Command Set

BIT-MAPPED REGISTER S14

Format

AT [cmds] S14=n [cmds]

Example:

ATS14=138<CR>

Default:

138

Range:

0-174

Unit:

Bit-mapped.

Description:

Controls echo, result codes, result code display, dial mode, and answer/originate mode.

Bit

Value

Function

0

0

Not used.

1

0

» 1

Command echo disabled.

Command echo enabled.

2

» 0

1

Result codes enabled.

Result codes disabled.

3

0

» 1

Display result codes in numeric format.

Display result codes in verbose format.

4

0

Not used.

5

» 0

1

Tone dial enabled.

Pulse dial enabled.

6

0

Not used.

7

0

» 1

Answer mode enabled.

Originate mode enabled.

BIT-MAPPED REGISTER S21

Format

AT [cmds] S21=n [cmds]

Example:

ATS21=48<CR>

Default:

48

Range:

0 - 253

Unit:

Bit-mapped

Description:

Selects serial port speed option, CTS signal, low DTR action, DCD signal, DSR signal, and the Long Space Disconnect function.

Note:

For bit 1 please see bits 1-3 of S23.

Bit

Value

Function

0

0

Not used.

1

» 0

1

Select serial speed option 1 (S23).

Select serial speed option 2 (S23).

2

0

» 1

CTS follows RTS.

CTS forced high.

4, 3

00

01

» 10

11

DTR signal ignored.

Modem goes to command mode on low DTR.

Modem disconnects on low DTR. Auto-Answer is disabled.

Modem is initialized on low DTR.

5

0

» 1

DCD forced high.

DCD normal.

6

» 0

1

DSR forced high.

DSR normal.

7

» 0

1

Long Space Disconnect function disabled.

Long Space Disconnect function enabled.

BIT-MAPPED REGISTER S22

Format

AT [cmds] S22=n [cmds]

Example:

ATS22=118<CR>

Default:

118

Range:

0 - 255

Unit:

Bit-mapped.

Description:

Controls volume and speaker settings, result codes, and make/break pulse ratio.

Bit

Value

Function

1, 0

00

01

» 10

11

Lowest volume setting.

Low volume setting.

Medium volume setting

Highest volume setting.

3, 2

00

» 01

10

11

Speaker disabled.

Speaker enabled until carrier signal detected

Speaker enabled.

Speaker enabled following dialing, then disabled after carrier signal detected.

6, 5 ,4

000

100

101

110

» 111

Busy and dialtone detection disabled, result codes 0-4 enabled.

Busy and dialtone detection disabled, result codes 0-5, 10 enabled.

Busy tone detection disabled, dialtone detection enabled, result codes 0-6, 10 enabled.

Busy tone detection enabled, dialtone detection disabled, result codes 0-5, 7, 10 enabled.

Busy and dialtone detection enabled, result codes 0-7, 10 enabled.

7

» 0

1

39/61ms at 10pps (North America)

33/67ms at 10pps (Europe)

BIT-MAPPED REGISTER S23

Format

AT [cmds] S23=n [cmds]

Example:

ATS23=11<CR>

Default:

11

Range:

0-255

Unit:

Bit-mapped

Description:

Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone.

Note: Option 1 and 2 in bit 1-3 is selected by S21.

Bit

Value

Function

0

0

» 1

Remote digital loopback denied.

Remote digital loopback allowed.

3, 2, 1

000

» 001

010

011

101

110

111

Option 1

Sets serial port speed to 0-300bps.

Sets serial port speed to 1200bps.

Sets serial port speed to 2400bps.

Sets serial port speed to 4800bps.

Sets serial port speed to 9600bps.

Sets serial port speed to 19200bps.

Sets serial port speed to 38400bps.

Option 2

Sets serial port speed to 12Kbps.

Sets serial port speed to 14.4Kbps.

Sets serial port speed to 57.6Kbps.

5,4

» 00

01

10

11

Parity even.

No Parity.

Parity odd.

Mark Parity

7, 6

» 00

10

11

Guard tone disabled.

Guard tone 550Hz enabled.

Guard tone 1800Hz enabled.

BIT-MAPPED REGISTER S27

Format

AT [cmds] S27=n [cmds]

Example:

ATS27=64<CR>

Default:

64

Range:

0 - 255

Unit:

Bit-mapped

Description:

Controls communications mode, line type, and protocol type.

Note:

Be aware that bits 2 and 3 are out of order.

Bit

Value

Function

1 - 0

0

Not used.

5 - 3

0

Not used.

6

0

» 1

Select CCITT protocols.

Select Bell protocols.

7, 2

» 00

01

11

Switched line.

Leased line.

Leased line autoconnect.

TEST MODES

Format

AT [cmds] S16=n [cmds]

Example:

ATS16=40<CR>

Default:

0

Range:

0-125

Unit:

Bit-mapped

Description:

Controls loopback tests, analog, digital, remote digital, and self tests.

Bit

Value

Function

0

» 0

1

Local analog loopback not in progress.

Local analog loopback in progress.

1

0

Not used.

2

» 0

1

Local digital loopback not in progress.

Local digital loopback in progress.

3

» 0

1

Modem not in remote digital loopback.

Remote digital loopback in progress.

4

» 0

1

Remote digital loopback not requested.

Remote digital loopback requested.

5

» 0

1

Remote digital loopback w/ self-test not in progress.

Remote digital loopback w/ self-test in progress.

6

» 0

1

Local analog loopback w/ self-test not in progress.

Local analog loopback w/ self-test in progress.