MAXTECH CORPORATION
XPVS288R9 (SF-1128HV/R9)
|
Card Type |
Modem, Fax |
|
Chip Set |
Unidentified |
|
I/O Options |
Line in, line out, microphone in, speaker out |
|
Maximum Modem Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half-length, full-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
Microphone in |
CN3 | |||
|
Line in |
CN2 |
Speaker out |
CN4 | |||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
Microphone set for dynamic |
JP2 |
Pins 1 & 2 closed |
|
Microphone set for condenser |
JP2 |
Pins 2 & 3 closed |
|
Speaker set for stereo |
JP4 |
Closed |
|
Speaker set for mono |
JP4 |
Open |
|
í Plug and Play enabled |
PNP1 |
Closed |
|
Plug and Play disabled |
PNP1 |
Open |
|
SERIAL PORT ADDRESS | |||
|
Setting |
PNP1 |
SW1/1 |
SW1/2 |
|
COM1 (3F8h) |
Open |
On |
On |
|
COM2 (2F8h) |
Open |
Off |
On |
|
COM3 (3E8h) |
Open |
On |
Off |
|
COM4 (2E8h) |
Open |
Off |
Off |
|
í PnP |
Closed |
Off |
Off |
|
IRQ SETTINGS | |||||
|
Setting |
PNP1 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
|
2/9 |
Open |
On |
Off |
Off |
Off |
|
3 |
Open |
Off |
On |
Off |
Off |
|
4 |
Open |
Off |
Off |
On |
Off |
|
5 |
Open |
Off |
Off |
Off |
On |
|
í PnP |
Closed |
Off |
Off |
Off |
Off |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, A/ |
|
A, E, H, M, O, P, T, V, X, Y, Z |
|
&C, &G, &L, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \C, \E, \G, \J, \K, \O, \Q, \U, \X, \Y, \Z |
|
%A |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26, |
|
S27 |
|
Special Commands |
|
#BDR, #CLS, #MDL?, #MFR?, #REV?, #SPK=a,b,c, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, |
|
#VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
í &M0 |
Asynchronous mode |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. | |
|
Command |
Protocol |
|
B0 |
Enables CCITT mode |
|
B1 |
Enables Bell mode |
|
B2 |
Enables Autoscan mode |
|
B3 |
Enables CCITT V.23 mode only |
|
B4 |
Enables 300 bps connection only |
|
B5 |
Enables 1200 bps connection only |
|
B6 |
Enables 2400 bps connection only |
|
B7 |
Enables 4800 bps connection only |
|
B8 |
Enables 9600 bps connection only |
|
B9 |
Enables 14400 bps connection only |
|
B10 |
Enables 16800 bps connection only |
|
B11 |
Enables 19200 bps connection only |
|
B12 |
Enables 21600 bps connection only |
|
B13 |
Enables 24000 bps connection only |
|
B14 |
Enables 26400 bps connection only |
|
B15 |
Enables 28800 bps connection only |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
í Command 0 |
Modem does not respond to DTR |
|
Command 1 |
Modem goes to command mode after DTR goes is off |
|
Command 2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
Command 3 |
Modem is initialized after DTR goes off |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DP |
Pulse dialing enabled |
|
DR |
Answer mode enabled; originate mode disabled following handshake initiation. |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
í &S1 |
DSR high only while modem is handshaking or connected |
|
FACTORY DEFAULT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Fn [cmds] |
|
Description: |
Recalls factory default configuration and/or with software flow control enabled |
|
Command |
Function |
|
í &F0 |
Recalls factory default configuration |
|
&F1 |
Recalls factory default configuration with software flow control enabled |
|
&F2 |
Recalls factory default configuration with hardware flow control enabled |
|
&F3 |
Recalls factory default configuration with software flow control enabled and ignores the DTR signal |
|
&F4 |
Recalls factory default configuration with hardware flow control enabled and ignores the DTR signal |
|
&F5 |
Set modem to Direct mode |
|
FALL FORWARD/FALL BACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &En [cmds] |
|
Description: |
Enables/Disables fall forward/fall back |
|
Command |
Function |
|
í &E0 |
Disables automatic fall forward/fall back |
|
&E1 |
Enables automatic fall forward/fallback |
|
HELP | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &H [cmds] |
|
Description: |
Displays the modem help screen |
|
ORIGINATE MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &On [cmds] |
|
Description: |
Enables/Disables originate-only mode |
|
Command |
Mode |
|
í &O0 |
Originate-only mode disabled |
|
&O1 |
Originate-only mode enabled |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe & Hong Kong) |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested and configures Plug and Play serial number |
|
Command |
Function |
|
I0 |
Reports product ID |
|
I1 |
Reports ROM checksum |
|
I2 |
Tests and reports internal memory |
|
I3 |
Reports V.42bis ID |
|
I4 |
Reports internal ID |
|
I99=n |
Configures Plug and Play serial number to n (n = 0-225) |
|
RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Enables modem to send result codes to the DTE |
|
Command |
Function |
|
í Q0 |
Result code sending enabled |
|
Q1 |
Result code sending disabled |
|
Q2 |
Result code sending disabled only when answer mode is enabled |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
Extended AT Command Set
|
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall-forward |
|
Command |
Function |
|
%E0 |
Auto-retrain disabled |
|
í %E1 |
Auto-retrain enabled |
|
AUTO-DETECT SETTINGS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Mn [cmds] |
|
Description: |
Controls V.34 and V.FC while in auto-detect mode |
|
Command |
Function |
|
í %M0 |
Sets V.34 and V.FC to auto-detect mode |
|
%M1 |
Sets only V.34 to auto-detect |
|
%M2 |
Sets only V.FC to auto-detect |
|
CLEAR-DOWN SIGNAL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Dn [cmds] |
|
Description: |
Enables/Disables clear-down signal |
|
Command |
Function |
|
%D0 |
Clear-down signal disabled |
|
í %D1 |
Clear-down signal enabled |
|
COMPRESSION/CORRECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression and correction |
|
Command |
Function |
|
%C0 |
Data compression and correction disabled |
|
%C1 |
MNP5 and V.42bis; or data compression and correction enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
MNP reliable mode enabled |
|
\N3 |
Auto-reliable mode or MNP auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
\N5 |
V.42 auto-reliable mode or MNP auto-reliable mode enabled |
|
\N6 |
V.42/MNP/Normal data link enabled |
|
DCE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Vn [cmds] |
|
Description: |
Reports DCE speed and extended responses |
|
Command |
Function |
|
í \V0 |
Reports DCE speed without sending extended responses |
|
\V1 |
Reports DCE speed and send sends extended responses |
|
\V2 |
Reports DTE speed without sending extended responses |
|
\V3 |
Reports DTE speed and send sends extended responses |
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Default: |
0 |
|
Range: |
0-90 |
|
Unit: |
1 minute |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
LINE SIGNAL LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Ln [cmds] |
|
Default: |
11 |
|
Range: |
0-15 |
|
Unit: |
dBm |
|
Description: |
Returns a value which indicates the received line signal level |
|
PASSWORD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \P=x [cmds] |
|
Description: |
Stores password x (x=ASCII characters 1 through 127 excluding "?" maximum 7 characters) stored into non-volatile RAM |
|
POWER-ON AUTO-CONNECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Pn [cmds] |
|
Description: |
Enables/Disables power-on auto-connect |
|
Command |
Function |
|
í %P0 |
Power-on auto-connect disabled |
|
%P1 |
Power-on auto-connect enabled |
|
SECURITY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Sn [cmds] |
|
Description: |
Enables/Disables call-back security and checks password |
|
Command |
Function |
|
í %S0 |
Call-back security disabled |
|
%S1 |
Password check enabled |
|
%S2 |
Call-back security and password check enabled |
S(status) -Registers
|
BIT-MAPPED REGISTER S28 | |
|
Type: |
Register |
|
Format |
AT [cmds] S28=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Configures Power-on auto-connect, security call-back, auto-retrain, and Bell/CCITT mode settings |