COMPEX, INC.
ANET16-1A
|
NIC Type |
ARCnet |
|
Transfer Rate |
2.5Mbps |
|
Data Bus |
16-bit ISA |
|
Topology |
Star Linear Bus |
|
Wiring Type |
Shielded/Unshielded twisted pair RG-62A/U 93ohm coaxial |
|
Boot ROM |
Available |
|
NODE ADDRESS | ||||||||
|
Node |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 |
|
0 |
- |
- |
- |
- |
- |
- |
- |
- |
|
1 |
Off |
On |
On |
On |
On |
On |
On |
On |
|
2 |
On |
Off |
On |
On |
On |
On |
On |
On |
|
3 |
Off |
Off |
On |
On |
On |
On |
On |
On |
|
4 |
On |
On |
Off |
On |
On |
On |
On |
On |
|
251 |
Off |
Off |
On |
Off |
Off |
Off |
Off |
Off |
|
252 |
On |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
253 |
Off |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
254 |
On |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
255 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
Note:Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1) | ||||||||
|
INTERRUPT REQUEST | ||||||
|
IRQ |
JP1 |
JP2 |
JP3 |
JP4 |
JP5 | |
| » |
2/9 |
Open |
Open |
Open |
Open |
Closed |
|
3 |
Open |
Open |
Open |
Closed |
Open | |
|
4 |
Open |
Open |
Closed |
Open |
Open | |
|
5 |
Open |
Closed |
Open |
Open |
Open | |
|
7 |
Closed |
Open |
Open |
Open |
Open | |
|
I/O ADDRESS | ||||
|
Address |
JP6 |
JP7 |
JP8 | |
|
260h |
Closed |
Closed |
Closed | |
|
290h |
Closed |
Closed |
Open | |
| » |
2E0h |
Closed |
Open |
Closed |
|
2F0h |
Closed |
Open |
Open | |
|
300h |
Open |
Closed |
Closed | |
|
350h |
Open |
Closed |
Open | |
|
380h |
Open |
Open |
Closed | |
|
3E0h |
Open |
Open |
Open | |
|
Note:Jumpers count from right to left in the diagram. | ||||
|
BOOT ROM | ||
|
Setting |
JP14 | |
| » |
Disabled |
Open |
|
Enabled |
Closed | |
|
BASE ADDRESS AND BOOT ROM ADDRESS | ||||||
|
Address |
Boot ROM Address |
JP9 |
JP10 |
JP11 |
JP12 |
JP13 |
|
C0000h |
C2000h |
Closed |
Closed |
Closed |
Closed |
Closed |
|
C4000h |
C6000h |
Closed |
Closed |
Open |
Closed |
Closed |
|
CC000h |
CE000h |
Closed |
Open |
Closed |
Closed |
Closed |
|
D0000h |
D2000h |
Closed |
Open |
Open |
Closed |
Closed |
|
D4000h |
D6000h |
Open |
Closed |
Closed |
Closed |
Closed |
|
D8000h |
DA000h |
Open |
Closed |
Open |
Closed |
Closed |
|
DC000h |
DE000h |
Open |
Open |
Closed |
Closed |
Closed |
|
E0000h |
E2000h |
Open |
Open |
Open |
Closed |
Closed |
|
Note:Jumpers count from right to left in the diagram. | ||||||
|
WAIT STATE | ||
|
Setting |
JP15 | |
| » |
Zero wait states disabled |
Open |
|
Zero wait states enabled |
Closed | |
|
Note:If Zero wait states are enabled, IOCHRDY (JP20) must be disabled. | ||
|
CABLE TYPE | ||||
|
Type |
Topology |
JP16 |
JP17 | |
| » |
RG62A/U 93ohm with terminator |
Star |
Pins 1 & 2 Closed |
Closed |
|
RG62A/U 93ohm without terminator |
Bus |
Open |
Closed | |
|
Shielded/Unshielded twisted pair |
Bus |
Pins 2 & 3 Closed |
Open | |
|
I/O CHANNEL READY | ||
|
Status |
JP20 | |
| » |
IOCHRDY signal disabled |
Open |
|
IOCHRDY signal enabled |
Closed | |
|
Note:If IOCHRDY signal is enabled, Zero wait state (JP15) must be disabled. If optional PROM is installed,
| ||