S T 1 9 1 7 1 N B A R R A C U D A 9 SEAGATE Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 5333| | | Capacity form/unform 9100/11700 MB Heads | | | Seek time / track 9.0/ 1.0 ms Sector/track | | | Controller SCSI3 SI/ULTR/FA Precompensation Cache/Buffer 512 KB MULTI-SEGMEN Landing Zone Data transfer rate 8.500 MB/S int Bytes/Sector 512 10.000 MB/S ext Recording method PRML 0/4/4 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 50 | -40 70 Power: sleep W Humidity % | standby W Altitude km | idle 12.4 W Shock g | seek W Rotation RPM 7200 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 1000000 Warranty Month 60 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** SEAGATE ST19171N/ND INSTALLATION GUIDE 83329020 REV. A 2/96 +---------------------------------------+----------1------+ 1-+ +----------+J2 |XX | |J6 |XXI | | |XXN | | |XXT +-+ N/ND MODEL |XXE | |XXR | |XXF | |XXA | |XXC | |XXE | |XX | |XX | |XX | | 1 | |XX Power | |XX +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** SEAGATE ST19171N INSTALLATION GUIDE 83329020 REV. A 2/96 Jumper Setting ============== J6 Setting the SCSI ID jumpers ------------------------------ Use the J6 connector to set the SCSI ID. To change the SCSI ID, install jumpers on the appropriate pins as shown. | ---+--------+----------------+-+ | * * * *|* * * * * * * 1 | | * * * *|* * * * * * * * |J6 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * * * 1 | | * * * *|* * * * * * * * |J6 SCSI ID 0 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * * * X | | * * * *|* * * * * * * X |J6 SCSI ID 1 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * * X 1 | | * * * *|* * * * * * X * |J6 SCSI ID 2 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * * X X | | * * * *|* * * * * * X X |J6 SCSI ID 3 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * X * 1 | | * * * *|* * * * * X * * |J6 SCSI ID 4 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * X * X | | * * * *|* * * * * X * X |J6 SCSI ID 5 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * X X 1 | | * * * *|* * * * * X X * |J6 SCSI ID 6 +--------+----------------+ ---+RESERVED+----------------+ | * * * *|* * * * * X X X | | * * * *|* * * * * X X X |J6 SCSI ID 7 +--------+----------------+ J2 Terminating the drive ------------------------ ST19171N drives are terminated with permanently mounted IC active terminators. If you install one of these drives and it is not on the end of the SCSI bus, disable the terminators by removing the jumper from pins 15 and 16 of connector J2. If you install the drive on the end of the SCSI bus, enable termination by installing a jumper on pins 15 and 16 of connector J2. +---------------+ --+* * * * * * * 1+-- J2 * * * * * * * * T D M W P E T T E S E P D S P P +---------------+ --+X . . . . . . 1+-- J2 Enable SCSI terminator (default) X . . . . . . . +---------------+ --+* . . . . . . 1+-- J2 Disable SCSI terminator * . . . . . . . Terminator Power ---------------- There are three posiible terminator power configurations for ST19171N drives. You will not normally need to change this option and can leave the drive configured as it was shipped from the factory. +---------------+ --+. . . . . . X 1+-- J2 Terminator Power from Drive (DEFAUlLT) . . . . . . X * +---------------+ --+. . . . . . * X+-- J2 Terminator Power to SCSI Bus . . . . . . * X +---------------+ --+. . . . . . * 1+-- J2 Terminator Power from SCSI BUS . . . . . . xxx Other applicable jumper options ------------------------------- +---------------+ --+. . . . . * . 1+-- J2 RESERVED . . . . . * . . Delay Motor Start option ------------------------ Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected) +---------------+ --+. * . . . . . 1+-- J2 Disable the Delay Motor Start option . * . . . . . . (default) +---------------+ --+. X . . . . . 1+-- J2 Motor start delay equal to the SCSI ID . X . . . . . . multiplied by 12 seconds. For example, if the SCSI ID = 2, the drive starts in 24 seconds. Motor Start option ------------------ +---------------+ --+. . * . . . . 1+-- J2 Disable motor start (default). The drive . . * . . . . . starts according to the Delay Motor Start Option. +---------------+ --+. . X . . . . 1+-- J2 Enable motor start. The drive waits for the . . X . . . . . Start Unit command from the host before starting the spindle motor. Write Protect Option -------------------- +---------------+ --+. . . * . . . 1+-- J2 Write protect = Off (enables writing - . . . * . . . . default) +---------------+ --+. . . X . . . 1+-- J2 Write protect = ON (disables writing) . . . X . . . . Parity Check Option ------------------- +---------------+ --+. . . . * . . 1+-- J2 Enables parity check of SCSI bus (default) . . . . * . . . +---------------+ --+. . . . X . . 1+-- J2 Disables parity check . . . . X . . . J6 Jumper Options ----------------- | ---+--------+----------------+-+ | * * * *|. * * . . . . 1 | | * * * *|. * * . . . . . |J6 RESERVED +RESERVED+----------------+ | ---+--------+----------------+-+ | * * * *|* . . . . . . 1 | | * * * *|* . . . . . . . |J6 Remote LED +RESERVED+----------------+ ********************************************************************** I N S T A L L ********************************************************************** SEAGATE ST19171N/ND BARRACUDA 9 INSTALLATION GUIDE 83329020 REV. A Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). ********************************************************************** F E A T U R E S ********************************************************************** SEAGATE ST19171N/W/WD/WC/DC INSTALLATION GUIDE 83329020 REV. A Preface ------- This manual contains information for users of the Seagate ST19171 Barracuda 9 SCSI disc drives. It provides support services, performance specifications, and initial setup information. Electrostatic discharge protection ---------------------------------- Caution. Removal of circuit boards by personnel not performing depot repair will damage components and may void the warranty. All drive electronic assemblies are sensitive to static electricity, due to the electrostatically sensitive devices used within the drive circuitry. Although some devices such as metaloxide semiconductors are extremely sensitive, all semiconductors, as well as some resistors and capacitors, may be damaged or degraded by exposure to static electricity. Electrostatic damage to electronic devices may be caused by the direct discharge of a charged conductor or by exposure to the static fields surrounding charged objects. To avoid damaging drive electronic assemblies, observe the following precautions when installing or servicing the drive: - Ground yourself to the drive whenever the drive electronics are or will be exposed. Connect yourself to ground with a wrist strap (Seagate part number 12263496). Connection may be made to any grounded metal assembly. As a general rule, remember that you and the drive electronics must all be grounded to avoid potentially damaging static discharges. - Turn off the power before removing or installing the DC power cable. - Do not remove any circuit boards from the drive. - Never use an ohmmeter on any circuit boards. - When installing the drive on a carrier or tray, discharge the static electricity from the carrier or tray prior to inserting it into the system. Important safety information and precautions -------------------------------------------- Caution. Use forced-air ventilation when bench testing the drive to ensure proper cooling of drive components. Use proper safety and repair techniques for safe, reliable operation of this unit. Service should be done only by qualified persons. The procedures in this manual and labels on the unit contain warnings and cautions that must be carefully read and followed to minimize or eliminate the risk of personal injury. The warnings point out condi- tions or practices that may endanger you or others. The cautions point out conditions or practices that may damage the unit, possibly making it unsafe for use. Always observe the following warnings and precautions: - Perform all maintenance by following the procedures in this manual. - Follow all cautions and warnings in the procedures. - Use sound safety practices when operating or repairing the unit. - Use caution when troubleshooting a unit that has voltages present. Turn off power to the unit before servicing it. - Wear safety shoes when removing or replacing heavy parts. - Ensure that the internal temperature of the rack or cabinet does not exceed the limits defined for the drive when the drive is mounted in an equipment rack or cabinet. When units are stacked vertically, pay special attention to the top where temperatures are usually highest. - Do not remove any circuit boards from the drive chassis. Return the entire drive for depot repair if any circuit board is defective. Removal of circuit boards by personnel not performing depot repair will damage components and may void the warranty. - Do not remove the head and disc assembly (HDA) from the drive chassis. Return the entire drive for depot repair if the HDA is defective. - Do not attempt to disassemble the HDA. It is not field repairable. If the sealed HDA is opened by personnel not performing depot repair, this will damage compo-nents and void the warranty. As a component, this drive is designed to be installed and operated in accordance with UL1950, IEC950, EN60950, CSA C22.2 950, and VDE0805. Typical applications of these disc drives include customer packag- ing and subsystem design. Safety agencies conditionally certify component assemblies, such as the Barracuda disc drive, based on their final acceptability in the end-use product. The subsystem designers are responsible for meeting these conditions of accept- ability in obtaining safety, regulatory agency compliance in their end-use products and for certifying where required by law. A necessary part of meeting safety requirements is the provision for overcurrent protection on drive SELV supply voltages. This unit is a component part and as such is not meant to comply with FCC or similar national requirements as a standalone unit. Engineering radiated emissions test results are available through the Seagate Safety Department to assist the subsystem designer. General description ------------------- Barracuda 9 SCSI disc drives are high-speed, randomaccess digital- data storage devices. The drive is a component for installation in an enclosure designed for the drive. This is often a rack within the system or an external enclosure designed to house one or more disc drives or other peripheral units. In either case, the disc drive must receive adequate cooling and it must be sufficiently grounded and shielded from emissions. ********************************************************************** G E N E R A L ********************************************************************** SEAGATE SUPPORT SERVICES Seagate Technology ------------------ Technical Support Services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate(r) drive or other Seagate products, use one of the Seagate technical support services listed below. SeaFONE at 1-800-SEAGATE (1-800-732-4283) Seagate's 800 number allows toll-free access to automated self-help services, providing answers to commonly asked questions, troubleshooting tips and specifications for disc drives and tape drives. This service is available 24 hours daily and requires a touch-tone phone. If you need to speak to a technical support engineer, dial this number and listen to the options for technical support. (International callers can also reach this automated self-help service by dialing 408-456-4496). Seagate Technology online services Using a modem, you can obtain troubleshooting tips, free utility programs, drive specifications and jumper settings for Seagate's entire product line. You can also download software for installing and analyzing your drive. SeaNET You can obtain technical information on Seagate drives, Seagate software and much more over the Internet from Seagate's World Wide Web home page (http://www.seagate.com) or Seagate's ftp server (ftp://ftp.seagate.com). You may also send E-mail with your questions to DiscSupport@ Seagate.com or TapeSupport@Seagate.com. SeaBOARD SeaBOARD is a computer bulletin board system (BBS) that contains information about Seagate's disc and tape drive products and is available 24 hours daily. Set your communications software to eight data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers are listed in the following table. BBS Location Modem number United States Disc: 408-434-1080; Tape: 408-456-4415 England 44-1628-478011 France 33 1-48 25 35 95 Germany 49-89-140-9331 Singapore 65-292-6973 Thailand 662-531-8111 Australia 61-2-9756-2359 Taiwan 886-2-719-6075 Seagate CompuServe forum Online technical support for Seagate products is available on CompuServe. To access our technical support forum, type go seagate. This forum provides information similar to that found on SeaBOARD. In addition, you can type questions or browse through previous questions and answers on the forum messages. Seagate Technology FAX services SeaFAX You can use a touch-tone telephone to access Seagate's automated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Location Telephone number United States 1-800-SEAGATE or 408-456-4496 England 44-1628-894084 Australia 61-2-9756-5170 Seagate technical support FAX You can FAX questions or comments to technical support specialists 24 hours daily. Responses are sent during business hours. Location FAX number United States 408-944-9120 England 44-1628-890660 France 33 1-46 04 42 50 Germany 49-89-1430-5100 Australia 61-2-9725-4052 Singapore 65-293-4722 Hong Kong 852-2368 7173 Taiwan 886-2-715-2923 Korea 82-2-556-7294/4251 Seagate technical support You can talk to a technical support specialist during business hours Monday through Friday for one-on-one technical help. Before calling, note your system configuration and drive model number (STxxxx). There are several technical support phone numbers available for various Seagate products. Location Telephone number United States Please dial 1-800-SEAGATE for the specific product telephone number. (6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M., Pacific time, M-F) England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) France 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 5:00 P.M., M-F) Germany Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 4:00 P.M., M-F) Tape: 49-89-140-9333 Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F) Singapore 65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) Hong Kong 852-2368 9918 Taiwan 886-2-514-2237 Korea 82-2-556-8241 SeaTDD 408-944-9121 Using a telecommunications device for the deaf (TDD), you can send questions or comments 24 hours daily and exchange messages with a technical support specialist between 6:00 A.M. to 11:15 A.M. and 12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday. Customer Service Centers Seagate direct OEM, Distribution, System Integrator and Retail customers should contact your Seagate Service Representative for warranty information. Other customers contact your place of purchase. Seagate offers comprehensive customer support for all Seagate drives. Seagate customer service centers are the only facilities authorized to service Seagate drives. These services are available worldwide. Location Telephone number FAX number United States 1-800-468-3472; 405-949-6740 Other Americas (Canada & Brazil) 405-949-6706; 405-949-6738 Mexico 525-546-6965; 525-546-4888 Europe, Middle East & Africa 31-2065-43300; 31-2065-34320 Asia Pacific & Australia 65-485-3595; 65-485-4980 Japan 81-3-5462-2904; 81-3-3462-2979 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD, SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or registered trademarks of Seagate Technology, Inc. or one of its subsidiaries. All other trademarks or registered trademarks are the property of their respective owners.