D J A A - 3 1 7 0 0 D E S K S T A R IBM Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | 3308| | Capacity form/unform 1700/ MB Heads 4| 16| | Seek time / track 12.5/ ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 96 KB ADAP./SEGMEN Landing Zone Data transfer rate 10.000 MB/S int Bytes/Sector 512 16.600 MB/S ext PIO4 Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 65 Power: sleep W Humidity % 8 90 | 5 95 standby W Altitude km -0.300 3.048| -0.300 12.000 idle W Shock g 15 | seek W Rotation RPM 4500 read/write W Acoustic dBA spin-up W ECC Bit ON THE FLY,SMART MTBF h 350000 Warranty Month Lift/Lock/Park YES Certificates CSA,EN60950,FCC,IEC950,TUV... ********************************************************************** L A Y O U T ********************************************************************** IBM DJAA-31270/31700 JUMPER SETTING +---------------------------------------------------------+ | |XX Power | +------------ |xx | JP1 +++ |XXI | : | | |XXN AT | : | | Logic Card |XXT | JP7 +++ |XXE | | |XXR | | |XXF | | |XXA | | |XXC | | |XXE | +------+ |XX | +----- |XX1 | Back Side of the Drive | | |XX Power | |XX +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** IBM DJAA-31270/31700 JUMPER SETTING Jumper Setting ============== Jumpers are used for drive address setting, write cache disabling and auto re-allocation disabling. Jumper position and the function are as shown below. Pin pitch is 2mm. JP2 JP3 JP5 JP6 JP1 Slave Cable Write RESERVED Master | Selection Cache | | | | JP4 | | JP7- RESERVED +--+ +--+ +--+ +--+ +--+ +--+ +--+ |1 | |3 | |5 | |7 | |9 | |11| |13| +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ +--+ |2 | |4 | |6 | |8 | |10| |12| |14| +--+ +--+ +--+ +--+ +--+ +--+ +--+ --------------------------------------- -----------Raw-Card-------------------- NOTES 1. Jumpers for JP1, 2, and 3 should not be selected concurrently. 2. JP1 is for Master, JP2 is for Slave, JP3 is for Cable Selection mode. 3. To enable Cable Selection mode, the JP3 jumper must be installed. In the Cable Selection mode, the drive address is determined as follows: - When CSEL signal (pin 28) is grounded or at a low level, the drive address is 0 (master). - When CSEL signal is open or at high level, the drive address is 1 (slave). 4. Position JP4, JP6 and JP7 are reserved. 5. A jumper for JP5 is used to disable write-cache (default). Write cache jumper is checked during the initial POR check. Write cache is disabled when a jumper is fitted and in this case a 'Set features'command to switch Write cache 'on'or 'off' will be aborted by the drive. Default Setting --------------- The default jumper setting at shipment is as follows. Position:|JP1| JP2| JP3| JP4| JP5 | Pin: |1-2| 3-4| 5-6| 7-8| 9-10| ---------+---+----+----+----+-----+ Jumper: | ON| OFF| OFF| OFF| OFF | | | | | +-------------- Write Cache enabled | | | +------------------- Not Used (RESERVED) | | +------------------------ Cable Selection | | disabled | +----------------------------- Slave not assigned +---------------------------------- Master assigned, and appropreate for single drive present. ********************************************************************** I N S T A L L ********************************************************************** IBM DJAA-31270/31700 JUMPER SETTING Notes on Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). The maximum allowable penetration of the mounting screws is 1 3.5mm 2 6mm. The recommended mounting screw torque is 3 0.5 [KgF.cm]. Identification Labels --------------------- The following labels are affixed to every hard disk drive shipped from the manufacturing location in accordance with appropriate hard disk drive assembly drawing. - A label contaning the IBM logo, IBM part number and the statement "Made by IBM Japan Ltd.". - A label containing the drive model number, date code, formatted capacity, place of manufacture, and UL/CSA/TUV logos. - A bar code label containing the drive serial number. - An user designed label per agreement. The labels may be integrated with the other labels. Cabling ------- The maximum cable length from the host system to the HDD, plus the circuit pattern length in the host system, cannot exceed 18 inches (45.7 cm). For higher data transfer application (>8.3MB/sec) the cable length should be shorter than 18 inches (45.7cm) since data transfer characteristics depends on the driver circuits of the system and hard drive, and or cabling. Connectors ---------- There is a choice of 2 power connections to this drive. One DC power connector is designed to mate with AMP part 1-480424-0 (using AMP pins P/N 350078-4). The other (3 pin) DC power connector is designed to mate with MOLEX 5480-03 (using MOLEX pins 5479). Equivalent connectors may be used. Pin assignments are shown below. +-----+ +-------+ |3 2 1| |4 3 2 1| +-----+ +-------+ | | +- +5V | | | +-- +12V | +--- +12V | | +---- GND +----- GND | +------ GND +-------- +5V AT Signal Connector ------------------- The AT signal connector is a 40-pin connector. The drive uses single-ended drivers and receivers. The connector is designed to mate with 3M part 3417-7000 or equivalent. NOTE It is intended that the hard disk drive should only be in electrical contact with the chassis of the PC at a designated set of mounting holes. Other electrical contact may degrade error rate performance. As a result of this it is recommended that there should be no metal contact to the hard disk drive except at the mounting holes or the side rails into which the mounting holes tapped. ********************************************************************** F E A T U R E S ********************************************************************** IBM DJAA-31270/31700 JUMPER SETTING Automatic Power Down Sequence ----------------------------- A hard reset will disable the automatic power down sequence. Format Track ------------ A drive will not perform a physical format. Instead it will simply write a data pattern of all zeros to the sectors which have been specified by the Format Track command. LBA mode for format track is not supported.