WISECOM, INC.

WS-5614JS3/ES3 (INTERNAL)

Card Type

Modem

Chip Set

Unidentified

I/O Options

Line out, line in, speaker out, microphone in

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.22, V.22bis, V.32, V.32bis, V.34, 56Kflex

Fax Modulation Protocol

ITU-T V.17, V.21 CH.2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

8-bit ISA

CONNECTIONS

Function

Label

Function

Label

Line out (RJ-11)

CN1

Speaker out

CN3

Line in (RJ-11)

CN2

Microphone in

CN4

PLUG & PLAY

Setting

JP3

JP4

? Plug & play enabled

Pins 1 & 2 closed

Pins 1 & 2 closed

Plug & play disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

SERIAL PORT ADDRESS

Setting

SW1/1

SW1/2

COM1 (3F8h)

On

On

COM2 (2F8h)

Off

On

COM3 (3E8h)

On

Off

COM4 (2E8h)

Off

Off

INTERRUPT

IRQ

SW1/3

SW1/4

SW1/5

SW1/6

2

On

Off

Off

Off

3

Off

On

Off

Off

4

Off

Off

On

Off

5

Off

Off

Off

On

 

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, B, E, H, V

&C, &M, &P, &T, &V, &W, &X, &Y, &Z

Extended AT Commands

%C, %E, %L, %Q

\A, \B, \K, \N

Special Commands

 

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25

S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S91, S92, S95

Note: See MHI Help File for full command documentation.

PROPRIETARY AT COMMAND SET

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Selects communications mode options

Command

Mode

&Q0

Asynchronous mode, serial port speed follows connect speed.

&Q1

Asynchronous off-line command mode and synchronous connect mode.

&Q2

Asynchronous off-line command mode - modem autodials first number in directory, then synchronous connect mode.

&Q3

Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR.

? &Q5

Error correction mode

&Q6

Buffered asynchronous mode

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Mode

&D0

DTR ignored

&D1

DTR toggle causes online command mode

? &D2

DTR toggle causes modem to go on-hook

&D3

Modem reset on DTR toggle

 

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

&F0

Load factory configuration 0

&F1

Load factory configuration 1

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Transparent XON/XOFF flow control enabled

? &K6

Both RTS/CTS & XON/XOFF flow control enabled

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Note: Used primarily for international data transmission

Command

Function

? &G0

Guard tone disabled

&G1

550Hz guard tone enabled

&G2

1800Hz guard tone enabled

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem model and speed

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports product ID string

I6

Reports diagnostic information

I7

Reports product configuration

 

RESTORE PROFILE ON POWER-UP

Type:

Configuration

Format:

AT [cmds] Yn [cmds]

Description:

Restores a selected profile to default profile on power-up (hard reset)

Command

Function

? Y0

Restore stored profile 0 on power-up

Y1

Restore stored profile 1 on power-up

Y2

Load factory default configuration 0 on power-up

Y3

Load factory default configuration 1 on power-up

Y4

Load factory default configuration 2 on power-up

RTS/CTS

Type:

Configuration

Format:

AT [cmds] &Rn [cmds]

Description:

Selects RTS/CTS options

Command

Function

&R0

CTS follows RTS in data mode; RTS is ignored in command mode.

? &R1

CTS forced high, RTS is ignored.

SOFT RESET

Type:

Configuration

Format:

AT [cmds] Zn [cmds]

Description:

Restores modem profiles previously stored in non-volatile RAM using the &W command

Command

Function

? Z1

Restore stored profile 0

Z2

Restore stored profile 1

Z3

Load factory default configuration 0

Z4

Load factory default configuration 1

Z5

Load factory default configuration 2

SPEAKER MODE

Type:

Configuration

Format:

AT [cmds] Mn [cmds]

Description:

Selects various speaker options

Command

Function

M0

Speaker disabled

M1

Speaker enabled until carrier signal detected

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

? L2

Medium volume setting

L3

Highest volume setting

 

EXTENDED AT COMMAND SET

MODULATION SELECTION

Type:

Configuration

Format:

AT [cmds] +MS=x,y,z,a,b,c [cmds]

Description:

Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected.

Command

Function

x=0

V.21

x=1

V.22

x=2

V.22bis

x=3

V.23

x=9

V.32

x=10

V.32bis

x=11

V.34, K56flex

x=64

Bell 103

x=69

Bell 212A

y=0

Automode disabled

y=1

Auto-detect highest speed enabled

z, a=300

Set minimum or maximum transfer rate at 300bps, respectively.

z, a=1200

Set minimum or maximum transfer rate at 1200bps, respectively.

z, a=2400

Set minimum or maximum transfer rate at 2400bps, respectively.

z, a=4800

Set minimum or maximum transfer rate at 4800bps, respectively.

z, a=7200

Set minimum or maximum transfer rate at 7200bps, respectively.

z, a=9600

Set minimum or maximum transfer rate at 9600bps, respectively.

z, a=12000

Set minimum or maximum transfer rate at 12000bps, respectively.

z, a=14400

Set minimum or maximum transfer rate at 14400bps, respectively.

z, a=16800

Set minimum or maximum transfer rate at 16800bps, respectively.

z, a=19200

Set minimum or maximum transfer rate at 19200bps, respectively.

z, a=21600

Set minimum or maximum transfer rate at 21600bps, respectively.

z, a=24000

Set minimum or maximum transfer rate at 24000bps, respectively.

z, a=26400

Set minimum or maximum transfer rate at 26400bps, respectively.

z, a=28800

Set minimum or maximum transfer rate at 28800bps, respectively.

z, a=33600

Set minimum or maximum transfer rate at 33600bps, respectively.

b=0

m -law encoding

b=1

A -law encoding

c=0

Robbed bit signaling disabled

c=1

Robbed bit signaling enabled

S(Status) REGISTERS

CONNECTION FAILURE CODES

Type:

Register

Format

AT [cmds] S86? [cmds]

Description:

Reports codes which correspond to the possible causes of a connection failure

Value

Meaning

0

Normal hang up

4

Carrier signal lost

5

No error-control detected for remote modem during feature negotiation

9

No common protocol found

12

No failure - remote modem disconnected normally

13

Remote modem failed to respond after 10 re-transmissions same message

14

Violation of negotiated protocol caused failure