KINGSTON

KFM-PC144

Card Type

Fax, Modem (asynchronous)

Chip Set

Unidentified

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

PCMCIA Type II

Fax Class

Class I

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

V1912

Proprietary AT Command Set

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls auto-retrain mode and fallback/fall-forward

Command

Function

í %E0

Auto-retrain disabled

%E1

Auto-retrain enabled

%E2

Auto-fallback/fall-forward enabled

BIT-MAPPED REGISTER S14

Format:

AT [cmds] S14=n [cmds]

Default:

138

Range:

0-174

Unit:

Bit-mapped

Description:

Controls echo, result codes and display, dial mode, and answer/originate mode.

Bit

Value

Function

0

í 0

Not used

1

0

í 1

Command echo disabled

Command echo enabled

2

í 0

1

Result codes enabled

Result codes disabled

3

0

í 1

Display result codes in numeric format

Display result codes in verbose format

4

í 0

Not used

5

í 0

1

Tone dial enabled

Pulse dial enabled

6

í 0

Not used

7

0

í 1

Answer mode enabled

Originate mode enabled

BIT-MAPPED REGISTER S21

Format

AT [cmds] S21=n [cmds]

Default:

52

Range:

0-252

Unit:

Bit-mapped

Description:

Selects CTS/DCD/DSR signals, low DTR action, and the long space disconnect function.

Bit

Value

Function

0, 1

í 00

Not used

2

0

í 1

CTS forced high

CTS follows RTS

4, 3

00

01

í 10

11

DTR signal ignored

Modem goes to command mode on low DTR

Modem disconnects on low DTR; Auto-Answer is disabled.

Modem is initialized on low DTR

5

0

í 1

DCD forced high

DCD normal

6

í 0

1

DSR forced high

DSR normal

7

í 0

1

Long space disconnect function disabled

Long space disconnect function enabled

BIT-MAPPED REGISTER S22

Format

AT [cmds] S22=n [cmds]

Default:

117

Range:

0-127

Unit:

Bit-mapped

Description:

Controls speaker volume and controls, and limits results codes.

Bit

Value

Function

1, 0

00

í 01

10

11

Volume off

Low level volume

Medium level volume

High level volume

3, 2

00

í 01

10

11

Speaker off

Speaker off on carrier

Speaker always on

Speaker on during handshake

6 - 4

000

100

101

110

í 111

Basic result codes only enabled

Basic and connection speed result codes enabled

Basic and connection speed result codes and dialtone detection enabled

All result codes except dialtone detection enabled

All result codes enabled

BIT-MAPPED REGISTER S23

Format

AT [cmds] S23=n [cmds]

Default:

183

Range:

0-189

Unit:

Bit-mapped

Description:

Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone.

Bit

Value

Function

0

0

í 1

Remote digital loopback denied

Remote digital loopback allowed

3 - 1

000

001

010

í 011

100

101

110

Sets serial port speed to 0-300bps

Sets serial port speed to 600bps

Sets serial port speed to 1200bps

Sets serial port speed to 2400bps

Sets serial port speed to 4800bps

Sets serial port speed to 9600bps

Sets serial port speed to 19200bps

5, 4

00

01

10

í 11

Parity even

Not used

Parity odd

No Parity

7, 6

00

01

í 10

Guard tone disabled

Guard tone disabled

Guard tone 1800Hz enabled

BIT-MAPPED REGISTER S27

Format

AT [cmds] S27=n [cmds]

Default:

9

Range:

0-75

Unit:

Bit-mapped

Description:

Selects asynchronous mode and ITU-T/Bell modes.

Bit

Value

Function

3, 1, 0

000

í 101

111

Asynchronous mode, serial port speed follows connect speed

Error correction mode

Buffered asynchronous mode

5, 4, 2

í 000

Not used

6

í 0

1

ITU/T mode

Bell mode

BIT-MAPPED REGISTER S28

Format

AT [cmds] S28=n [cmds]

Default:

0

Range:

0-128

Unit:

Bit-mapped

Description:

Controls MNP10 link negotiation.

Bit

Value

Function

5 - 0

000000

Not used

7, 6

í 00

01

10

Link will be negotiated at highest possible speed

Link will be negotiated at 1200bps

Link will be negotiated at 4800bps

BIT-MAPPED REGISTER S31

Format:

AT [cmds] S31=n [cmds]

Default:

194

Range:

0-202

Description:

Select auto-mode and extended result code format.

Bit

Value

Function

0

í 0

Not used

1

0

í 1

Auto-mode detection disabled

Auto-mode detection enabled

3, 2

í 00

01

10

Enables CONNECT result codes to report DTE speed

Full reporting of CONNECT result codes

Enables CONNECT result codes to report DCE speed

7 - 4

í 1100

Not used

BIT-MAPPED REGISTER S40

Format

AT [cmds] S40=n [cmds]

Default:

105

Range:

0-238

Unit:

Bit-mapped

Description:

Controls MNP extended services, power level adjustment, break handling, and block size.

Bit

Value

Function

0, 1

00

í 01

10

Conversion disabled

Conversion enabled

Conversion enabled except during LAPM answer detection phase.

2

í 0

1

Power level adjustment enabled

Power level adjustment disabled

5, 4, 3

000

001

010

011

100

í 101

\K0

\K1

\K2

\K3

\K4

\K5

7, 6

00

01

10

í 11

MNP block size is 64 characters

MNP block size is 128 characters

MNP block size is 192 characters

MNP block size is 256 characters

BIT-MAPPED REGISTER S41

Format

AT [cmds] S41=n [cmds]

Default:

131

Range:

0-219

Unit:

Bit-mapped

Description:

Selects compression, auto-retrain, flow control, MNP mode and MNP10 fallback.

Bit

Value

Function

1, 0

00

01

10

í 11

Data compression disabled

MNP5 enabled

V.42bis enabled

MNP5 and V.42bis enabled

6, 2

í 00

01

10

Auto-retrain disabled

Auto-retrain enabled

Auto-fallback/fall-forward enabled

3

í 0

1

Flow control disabled

Flow control enabled

4

í 0

1

Stream mode for MNP

Block mode for MNP

5

í 0

Not used

7

0

í 1

MNP10 at 2400 and 1200bps disabled

MNP10 at 2400 and 1200bps enabled

BIT-MAPPED REGISTER S201

Format:

AT [cmds] S201=n [cmds]

Default:

58

Range:

0-62

Description:

Controls power level, and compromise equalizer.

Bit

Value

Function

4 - 0

00000

00001

00010

...

01010

01011

...to...

í 11010

...to...

11110

Initial power level -26dBm

Initial power level -30dBm

Initial power level -10dBm

...

Initial power level -10dBm

Initial power level -11dBm

...to...

Initial power level -26dBm

...to...

Initial power level -30dBm

5

0

í 1

Equalizer disabled

Equalizer enabled

BREAK SEND

Type:

Configuration

Format:

AT [cmds] \Bn [cmds]

Default:

3

Range:

1-9

Unit:

.1 second

Description:

Sends break to modem

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Description:

Configures action of break signal

Command

Break from DTE

Modem receives \B

Break received from remote modem

\K0

Online command mode enabled, send no break to remote modem

Break sent to remote modem and buffered cleared

Buffers cleared, break sent to DTE

\K1

Break sent to remote modem and buffered cleared

Break sent to remote modem and buffered cleared

Buffers cleared, break sent to DTE

\K2

Online command mode enabled, send no break to remote modem

Send break to remote modem immediately

Break sent immediately to DTE

\K3

Send break to remote modem immediately

Send break to remote modem immediately

Break sent immediately to DTE

\K4

Online command mode enabled, send no break to remote modem

Send break with transmitted data

Break sent with received data to the DTE

í \K5

Send break with transmitted data

Send break with transmitted data

Break sent with received data to the DTE

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

Data compression disabled

%C1

MNP5 enabled

%C2

V.42bis enabled

í %C3

MNP5 and V.42bis enabled

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Normal mode enabled

\N2

Reliable mode enabled

\N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

\N5

MNP auto-reliable mode enabled

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Modifier

Function

L

Re-dial last number

P

Pulse dialing enabled

Sn

Dial stored telephone number n (n=1-3)

S=n

Dial stored telephone number n (n=1-3)

T

Tone dialing enabled

W

Dialing resumed following dial tone detection

,

Dialing paused for amount of time specified in S8 register

@

Wait for quiet answer

;

Modem returned to command state after dialing

!

Modem commanded to go on-hook for specified time before returning off-hook.

^

Calling tone disabled for this call only

FLASH DIAL MODIFIER TIME

Type:

Register

Format

AT [cmds] S29=n [cmds]

Default:

0

Range:

0-255

Unit:

.01 second

Description:

Time the modem will go on-hook upon receiving the ! dial modifier in dial string.

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] \Gn [cmds]

Description:

Selects modem port flow control

Command

Function

í \G0

Flow control disabled

\G1

Flow control enabled

FLOW CONTROL

Type:

Read-only Register

Format

AT [cmds] S39? [cmds]

Description:

Displays the current flow control

Value

Meaning

0

Flow control disabled

3

RTS/CTS flow control enabled

4

XON/XOFF flow control enabled

5

XON/XOFF and RTS/CTS flow control enabled

FLOW CONTROL CHARACTER - XOFF

Type:

Register

Format:

AT [cmds] S33=n [cmds]

Default:

19

Range:

0-255

Unit:

ASCII

Description:

Sets the character used to represent XOFF

FLOW CONTROL CHARACTER - XON

Type:

Register

Format:

AT [cmds] S32=n [cmds]

Default:

17

Range:

0-255

Unit:

ASCII

Description:

Sets the character used to represent XON

INACTIVITY TIMER

Type:

Register

Format

AT [cmds] S30=n [cmds]

Default:

0

Range:

0-255

Unit:

10 seconds

Description:

Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process. S30=0 will disable timer.

LINE SIGNAL LEVEL

Type:

Immediate

Format:

AT [cmds] %L [cmds]

Description:

Returns a value which indicates the received line signal level

LINE SIGNAL QUALITY

Type:

Immediate

Format:

AT [cmds] %Q [cmds]

Description:

Returns a value which indicates line signal quality

LOCK SERIAL PORT

Type:

Configuration

Format:

AT [cmds] \Jn [cmds]

Description:

Sets operation of serial port speed

Command

Function

í \J0

Serial speed locked

\J1

Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION

Type:

Configuration

Format:

AT [cmds] \An [cmds]

Description:

Sets the maximum transmittable block size

Command

Function

\A0

MNP block size is 64 characters

\A1

MNP block size is 128 characters

\A2

MNP block size is 192 characters

í \A3

MNP block size is 256 characters

MNP - EXTENDED SERVICES

Type:

Configuration

Format:

AT [cmds] -Kn [cmds]

Description:

Controls conversion of a LAPM connection to MNP10 connection

Command

Function

-K0

Conversion disabled

í -K1

Conversion enabled

-K2

Conversion enabled except during LAPM answer detection phase.

MNP - STREAM/BLOCK MODE

Type:

Configuration

Format:

AT [cmds] \Ln [cmds]

Description:

Selects the transfer mode for MNP link

Command

Function

í \L0

Stream mode for MNP enabled

\L1

Block mode for MNP enabled

MNP10 - FALLBACK

Type:

Configuration

Format:

AT [cmds] -Qn [cmds]

Description:

Allows MNP10 to fall back to speeds slower than 4800bps

Command

Function

-Q0

MNP10 at 2400 and 1200bps disabled

í -Q1

MNP10 at 2400 and 1200bps enabled

MNP10 - LINK NEGOTIATION

Type:

Configuration

Format:

AT [cmds] *Hn [cmds]

Description:

Sets the speed at which MNP10 link negotiation will occur

Command

Function

*H0

Link will be negotiated at highest possible speed

*H1

Link will be negotiated at 1200bps

*H2

Link will be negotiated at 4800bps

MNP10 - POWER LEVEL ADJUST

Type:

Configuration

Format:

AT [cmds] )Mn [cmds]

Description:

Controls automatic transmit power level adjustment during MNP 10 link negotiation

Command

Function

í )M0

Power level adjustment disabled

)M1

Power level adjustment enabled

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code

I1

Reports ROM checksum

I2

Tests ROM and reports ‘OK’ or ‘ERROR’

I3

Reports ROM revision level

I4

Reports modem identifier string

I5

Report country code

I6

Reports data pump model

SLEEP TIMER

Type:

Register

Format

AT [cmds] S24=n [cmds]

Default:

32

Range:

0-255

Unit:

1 second

Description:

Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. S24=0 will disable timer.

TEST MODES

Type:

Register

Format:

AT [cmds] S16=n [cmds]

Default:

0

Range:

0-125

Unit:

Bit-mapped

Description:

Controls loopback tests, analog, digital, remote digital, and self tests.

Bit

Value

Function

0

í 0

1

Local analog loopback not in progress

Local analog loopback in progress

1

í 0

Not used

2

í 0

1

Local digital loopback not in progress

Local digital loopback in progress

3

í 0

1

Modem not in remote digital loopback

Remote digital loopback in progress

4

í 0

1

Remote digital loopback not requested

Remote digital loopback requested

5

í 0

1

Remote digital loopback w/ self-test not in progress

Remote digital loopback w/ self-test in progress

6

í 0

1

Local analog loopback w/ self-test not in progress

Local analog loopback w/ self-test in progress

TRANSMISSION LEVEL - CELLULAR

Type:

Configuration

Format:

AT [cmds] @Mn [cmds]

Default:

26

Range:

0-31

Unit:

-1dBm

Description:

Sets the signal level for transmission while in cellular mode

Command

Function

@M0

-26 dBm

@M1

-30 dBm

@M2-@M10

-10 dBm

V.23 MODE

Type:

Configuration

Format:

AT [cmds] %Fn [cmds]

Description:

Selects V.23 split-speed and half-duplex

Command

Function

%F1

75bps transmit, 1200bps receive (split-speed)

%F2

1200bps transmit, 75bps receive (split-speed)

V.32 - COMPROMISE EQUALIZER

Type:

Configuration

Format:

AT [cmds] :En [cmds]

Description:

Controls V.32 compromise equalizer

Command

Function

:E0

Equalizer disabled

í :E1

Equalizer enabled