E-TECH RESEARCH, INC.

C1414AX PCMCIA

Card Type

Modem(synchronous/asynchronous)

Chip Set

Unidentified

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

PCMCIA

Fax Class

Class I & II

Data Modulation Protocol

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Proprietary AT Command Set

V1795

BITS PER CHARACTER

Type:

Configuration

Format:

AT [cmds] $Ln [cmds]

Description:

Controls bits per character

Command

Function

$L0

8 bits per character

$L1

9 bits per character

í $L2

10 bits per character

$L3

11 bits per character

CARRIER DETECT

Type:

Configuration

Format:

AT [cmds] &Cn [cmds]

Description:

Controls DCD, Computer Systems Interface and Port Contender

Command

Function

&C0

DCD forced high

í &C1

DCD follows remote modem

&C2

Conforms to Computer Systems Interface

&C3

Conforms to Port Contender

CLEAR DOWN/DISCONNECT

Type:

Configuration

Format:

AT [cmds] Yn [cmds]

Description:

Controls long space disconnect and V.32 clear down

Command

Function

í Y0

Long space disconnect disabled

Y1

Long space disconnect enabled

Y2

V.32 clear down enabled

Y3

V.32 clear down and long space disconnect enabled

COMPRESSION

Type:

Configuration

Format:

AT [cmds] $Cn [cmds]

Description:

Controls data compression

Command

Function

$C0

Data compression disabled

í $C1

Data compression enabled

CONNECT/SPEED MESSAGE

Type:

Configuration

Format:

AT [cmds] $Xn [cmds]

Description:

Controls connect and speed message displayed

Command

Function

$X0

Normal connect and DCE speed message enabled

$X1

Normal connect and DTE speed message enabled

í $X2

Extended connect and DCE speed message enabled

$X3

Extended connect and DTE speed message enabled

DIAL INTERRUPT

Type:

Configuration

Format:

AT [cmds] $Kn [cmds]

Description:

Controls dial interrupt

Command

Function

$K0

Dial interrupt disabled

í $K1

Dial interrupt enabled

DISPLAY STORED INFORMATION

Type:

Configuration

Format:

AT [cmds] &Vn [cmds]

Description:

Displays stored phone numbers, configuration profiles and S registers

Command

Function

&V0

Display stored phone numbers

&V1

Display current configuration profiles

&V2

Display contents of S registers

&V3

Display stored profiles briefly

DSR SIGNAL

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Controls DSR, Computer Systems Interface and Port Contender

Command

Function

í &S0

DSR forced high

&S1

DSR follows remote modem

&S2

Conforms to Computer Systems Interface

&S3

Conforms to Port Contender

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] $Fn [cmds]

Description:

Controls XON/XOFF, ENQ/ACK, DTR/DSR AND CTS/RTS flow control

Command

Function

$F0

XON/XOFF enabled

$F1

XON/XOFF passthrough enabled

$F2

ENQ/ACK enabled

$F3

DTR/DSR enabled

í $F4

CTS/RTS enabled

$F5

Flow control disabled

LINE SPEED

Type:

Configuration

Format:

AT [cmds] &Ln [cmds]

Description:

Controls speed at which modem attempts to connect

Command

Function

í &L0

Line speed follows DTE speed

&L1

Connect at V.23 75/1200bps

&L2

Not used

&L3

Connect at 300bps

&L4

Not used

&L5

Connect at 1200bps

&L6

Connect at 2400bps

&L7

Connect at 4800bps

&L8

Connect at 7200bps

&L9

Connect at 9600bps

PROTOCOL

Type:

Configuration

Format:

AT [cmds] $En [cmds]

Description:

Controls protocol used

Command

Function

$E0

Normal mode

$E1

Auto MNP mode

$E2

MNP mode

í $E3

Auto V.42 mode

$E4

LAPM mode

RETRAIN LIMIT

Type:

Configuration

Format:

AT [cmds] &En [cmds]

Description:

Controls number of retrains per minute allowed

Command

Function

í &E0

Disconnect If more than four retrain attempts in three minutes

&E1

Disconnect If more than four retrain attempts in four minutes

&E2

Disconnect If more than four retrain attempts in five minutes

&E3

Unlimited retrain allowed

&E4

Retrain disabled

SPEED CONVERSION

Type:

Configuration

Format:

AT [cmds] $Sn [cmds]

Description:

Controls speed conversion

Command

Function

í $S0

Speed conversion enabled

$S8

Speed conversion disabled

TRANSMISSION LEVEL

Type:

Configuration

Format:

AT [cmds] $Tn [cmds]

Description:

Controls transmission level

Command

Function

$T0 - $T2

-4dBm

í -$T3

-6dBm

$T4

-8dBm

$T5

-10dBm

$T6

-12dBm

$T7

-14dBm

$T8

-16dBm