ARCHTEK CORPORATION

5634PCA-K

Card Type

Modem/Fax card

Chip Set

Cirrus Logic

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, K56flex

Fax Modulation Protocol

ITU-T V.17, V.27ter, V.29, T.4, T.30

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

PCMCIA

55075

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, E, H, L, M, P, Q, T, V, W, X, Y

&B, &C, &D, &G, &V, &Z

Extended AT Commands

\J, \T

%A, %G

Special Commands

+MS, -C

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S24, S30

 

Note: See MHI Help File for full command documentation.

PROPRIETARY AT COMMAND SET

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

In originate or answer mode, handshake occurs only in mode designated by the ATB command and S37 register.

í N1

In originate or answer mode, handshake begins at line speed designated by the S37 register and ATB command. Modem may shift to a lower speed

AUXILIARY RELAY CONTROL

Type:

Configuration

Format:

AT [cmds] &Jn [cmds]

Description:

Enables/disables A/A1 relay driver. Not for use with RJ-11 phone lines

Command

Jack Type

&J0

Auxiliary relay is never closed

COMMUNICATION PROTOCOLS

Type:

Configuration

Format:

AT [cmds] Bn [cmds]

Description:

Selects the communication protocol for data calls

Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.

Command

Protocol

B0

ITU-T V.22 at 1200bps or V.21 at 300bps

B1

Bell 212A at 1200bps/ Bell 103J at 300bps

B2

ITU-T V.23 at 75/1200bps originate; 1200/75bps answer

B3

ITU-T V.23 at 1200/75bps answer; 75/1200bps originate

B15

ITU-T V.22 at 1200bps or V.21 at 300bps

B16

Bell 212A at 1200bps/ Bell 103J at 300bps

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

&M0

Asynchronous mode

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Selects communications mode

Command

Mode

&Q0

Buffered asynchronous mode

&Q5

Error correction mode

&Q6

Buffered asynchronous mode

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

&D0

DTR override

&D1

DTR toggle causes online command mode

&D2

Normal DTR operations

&D3

Resets on receipt of DTR

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DL

Re-dial last number

DP

Pulse dialing enabled

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

D^

Data calling tone disabled

D$

Wait for credit card "bong" tone before processing the remaining characters in the dial string

ECHOPLEX VALIDITY

Type:

Configuration

Format:

AT [cmds] Fn [cmds]

Description:

Selects whether commands sent while in data mode are echoed

Command

Function

F1

Echoplex disabled

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

Command

Function

&F0

Sets values in active profile to factory settings

&F5

Sets values in active profile to factory settings for ETC mode

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K3

RTS/CTS hardware flow control enabled

&K4

XON/XOFF software flow control enabled

ON-LINE

Type:

Immediate

Format:

AT [cmds] On [cmds]

Description:

Controls on-line command (data transmission) state options.

Note: The O command must be placed at the end of the command string.

Command

Function

O0

On-line command mode disabled; return to data mode

O1

On-line command mode with retraining enabled

O2

Rate negotiation issued before returning to online command mode

PULSE DIALING RATIO

Type:

Configuration

Format:

AT [cmds] &Pn [cmds]

Description:

Selects pulse dial make/break ratio

Command

Function

í &P0

39/61ms at 10pps (North America)

&P1

33/67ms at 10pps (Europe)

&P2

33/67ms at 20pps

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem firmware revision information

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports modem firmware revision information

I12

Reports country code

RESTORE PROFILE ON POWER-UP

Type:

Configuration

Format:

AT [cmds] &Yn [cmds]

Description:

Restores a selected profile into the active profile on power-up (hard reset)

Command

Function

&Y0

Restore profile 0 on power-up

SOFT RESET

Type:

Immediate

Format:

AT [cmds] Zn [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

Command

Function

Z0

Restore setting 0

STORE ACTIVE PROFILE

Type:

Configuration

Format:

AT [cmds] &Wn [cmds]

Description:

Writes the values for the active profile into the non-volatile RAM

Command

Function

&W0

Write the active profile to stored profile 0

TEST MODES

Type:

Immediate

Format:

AT [cmds] &Tn

Description:

Selects test options

Command

Function

í &T0

End current test

&T1

Begin local analog loopback test

&T3

Begin local digital loopback request

&T6

Request remote digital loopback

TRANSMIT CARRIER

Type:

Configuration

Format:

AT [cmds] Cn [cmds]

Description:

Controls the transmit carrier switching

Command

Function

C1

Transmit carrier enabled

EXTENDED AT COMMANDS

BLACKLIST

Type:

Configuration

Format:

AT [cmds] %Bn [cmds]

Description:

Displays numbers which failed the last call attempt within two hours. In countries that do not require blacklisting, command returns ERROR

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Description:

Configures action of break signal

Command

Function

í \K5

Modem sends break to remote modem in sequence with transmitted data;

non-destructive/non-expedited

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Normal mode enabled

\N2

Reliable mode enabled

í \N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

\N5

MNP reliable mode enabled

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Description:

Sets type of flow control used by modem

Command

Function

\Q0

Flow control disabled

\Q1

Bi-directional XON/XOFF flow control enabled

í \Q2

RTS/CTS flow control to DTE enabled

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] \Gn [cmds]

Description:

Selects modem port flow control. For compatibility only.

Command

Function

\G0

Returns OK

XON/XOFF PASS-THROUGH

Type:

Configuration

Format:

AT [cmds] \Xn [cmds]

Description:

Selects whether XON/XOFF signals are sent to remote modem

Command

Function

\X0

XON/XOFF signals trapped by local modem

SPECIAL COMMANDS

IDENTIFY MODEM MANUFACTURER

Type:

Configuration

Format:

AT [cmds] +GMI? [cmds]

Description:

Commands DCE to send a message to the DTE indicating the DCE manufacturer

Note:

Modem manufacturers name may be changed using the firmware configuration utility

IDENTIFY PRODUCT MODEL

Type:

Configuration

Format:

AT [cmds] +GMM? [cmds]

Description:

Commands DCE to send a message to the DTE indicating the modem chipset name

Note:

Modem product model may be changed using the firmware configuration utility

IDENTIFY PRODUCT REVISION

Type:

Configuration

Format:

AT [cmds] +GMR? [cmds]

Description:

Commands DCE to send a message to the DTE indicating the modem chipset revision level

Note:

Modem chipset revision level may be changed using the firmware configuration utility

S(status) -REGISTERS

AUTO MODE

Format:

AT [cmds] S43=n [cmds]

Range:

0-1

Unit:

Unidentified

Description:

Enables/disables V.32bis start-up mode.

Note:

For testing and debugging purposes only

Command

Function

S43=0

V.32bis srtart-up mode disabled

S43=1

V.32bis srtart-up mode enabled

AUTO RATE

Format:

AT [cmds] S42=n [cmds]

Range:

0-1

Unit:

Unidentified

Description:

Enables/disables V.32 and V.22bis auto rate.

Note:

For testing and debugging purposes only

Command

Function

S42=0

V.32 and V.22bis auto rate disabled

S42=1

V.32 and V.22bis auto rate enabled

BIT-MAPPED REGISTER S14

Format:

AT [cmds] S14=n [cmds]

Range:

0-174

Unit:

Bit-mapped

Description:

Controls result codes display, and dial mode

Bit

Value

Function

2 - 0

0

Reserved

3

0

1

Display result codes in numeric format

Display result codes in verbose format

6

0 1

Pulse dial set to 10pps

Pulse dial set to 20pps

7

0

Reserved

BIT-MAPPED REGISTER S21

Format

AT [cmds] S21=n [cmds]

Range:

0-253

Unit:

Bit-mapped

Description:

Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function.

Bit

Value

Function

2 - 0

0

Reserved

4, 3

00

01

10

11

DTR signal ignored

Modem goes to command mode on low DTR

Modem disconnects on low DTR; Auto-Answer is disabled.

Modem is initialized on low DTR

5

0

í 1

DCD forced high

DCD normal

6, 7

0

Reserved

BIT-MAPPED REGISTER S22

Format

AT [cmds] S22=n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Controls speaker volume and controls, limits results codes, and pulse dial make/break ratio.

Bit

Value

Function

3 - 0

0

Reserved

6 - 4

000

100

101

110

111

Basic result codes only enabled

Basic and connection speed result codes enabled

Basic and connection speed result codes and dialtone detection enabled

All result codes except dialtone detection enabled

All result codes enabled

7

0

1

39/61ms at 10pps (North America)

33/67ms at 10pps (Europe)

DATA CALLING TONE

Format:

AT [cmds] S35=n [cmds]

Range:

0-1

Unit:

Unidentified

Description:

Enables/disables data calling tone. S35=0 disables

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Sets the maximum allowable data exchange rate attempted during handshake process.

Command

Function

S37=0

Maximum line speed

S37=2

1200/75bps

S37=3

300bps

S37=5

1200bps

S37=6

2400bps

S37=7

4800bps

S37=8

7200bps

S37=9

9600bps

S37=10

12.0Kbps

S37=11

14.4Kbps

S37=12

16.8Kbps

S37=13

19.2Kbps

S37=14

21.6Kbps

S37=15

24.0Kbps

S37=16

26.4Kbps

S37=17

28.8Kbps

S37=18

31.2Kbps

S37=19

33.6Kbps

56K DCE LINE SPEED

Type:

Register

Format

AT [cmds] S38=n [cmds]

Description:

Sets the maximum allowable 56K downstream rate attempted during handshake process.

Command

Function

S38=0

56K disabled

S38=1

56K automatic speed select

S38=2

32.0Kbps

S38=3

34.0Kbps

S38=4

36.0Kbps

S38=5

38.0Kbps

S38=6

40.0Kbps

S38=7

42.0Kbps

S38=8

44.0Kbps

S38=9

46.0Kbps

S38=10

48.0Kbps

S38=11

50.0Kbps

S38=12

52.0Kbps

S38=13

54.0Kbps

S38=14

56.0Kbps

S38=15

58.0Kbps

S38=16

60.0Kbps

ERROR CORRECTION NEGOTIATION

Type:

Register

Format

AT [cmds] S36=n [cmds]

Description:

Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q.

Command

Function

S36=0

Hang up

S36=1

Fall-back to asynchronous connection

S36=2

Hang up

S36=3

Fall-back to asynchronous connection

S36=4

Attempt a connection at MNP2-4; if that fails, hang up.

S36=5

Attempt a connection at MNP2-4; if that fails, fall-back to asynchronous connection

S36=6

Attempt a connection at MNP2-4; if that fails, hang up.

í S36=7

Attempt a connection at MNP2-4; if that fails, fall-back to asynchronous connection

ETC STARTUP AUTORATING

Type:

Register

Format

AT [cmds] S40=n [cmds]

Description:

Determines default auto-rating

Command

Function

S40=0

Start up with normal auto-rating

S40=1

Start up at initial rate of 4800bps or below

S40=2

Start up at initial rate of 9600bps or below

FEATURE NEGOTIATION OPTIONS

Type:

Register

Format:

AT [cmds] S48=n [cmds]

Description:

Selects active error correction and compression protocols

Command

Function

S48=7

Detection negotiation and XID negotiation enabled

S48=128

Fall-back to options set in S36

LOCAL PHONE STATUS

Type:

Register

Format:

AT [cmds] S90=n [cmds]

Description:

Displays the status of the local phone

Command

Function

S90=0

Local phone on-hook

S90=1

Local phone off-hook

SLEEP TIMER

Type:

Register

Format

AT [cmds] S89=n [cmds]

Range:

0, 5-255

Unit:

Unidentified

Description:

Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.

SYNTHETIC RING FREQUENCY

Format:

AT [cmds] S33=n [cmds]

Range:

1-5

Unit:

Unidentified

Description:

Determines synthetic ring frequency. S33=0 disables

SYNTHETIC RING VOLUME

Format:

AT [cmds] S32=n [cmds]

Range:

Unidentified

Unit:

-1dB

Description:

Determines synthetic ring volume

TRANSMISSION LEVEL - DIRECT CONNECT

Type:

Register

Format:

AT [cmds] S92=n [cmds]

Default:

20

Range:

Unidentified

Unit:

-1 dBm

Description:

Sets the signal level for transmission for direct connections

TRANSMISSION LEVEL - LINE

Type

Register or Configuration

Format

AT [cmds] S91=n [cmds]

Range

6-15

Unit

-1 dBm

Description

Sets the signal level for transmission over phone lines

Note:

Register only functions for Japan

V.34 MODULATION

Type:

Register

Format

AT [cmds] S28=n [cmds]

Range:

0-255

Unit:

Unidentified

Description:

Enables V.34 modulation protocol. S28=0 disables