C P - 3 0 1 0 4 CONNER NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1524| 762| 761| Capacity form/unform 122/ MB Heads 4| 8| 8| Seek time / track 19.0/ 8.0 ms Sector/track 39| 39| 39| Controller IDE / AT Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate 1.500 MB/S int Bytes/Sector 512 4.000 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep 0.5 W Humidity % 8 80 | 8 80 standby 0.5 W Altitude km -0.061 3.050| 12.200 idle 2.8 W Shock g 5 | 75 seek 3.9 W Rotation RPM 3400 read/write 3.8 W Acoustic dBA 40 spin-up W ECC Bit 56,SPLIT MTBF h 150000 Warranty Month 15 Lift/Lock/Park YES Certificates CSA,IEC435,TUV,UL478,VDE ********************************************************************** L A Y O U T ********************************************************************** CONNER CP30064/CP30084/CP30104 PRODUCT MANUAL 00501-045 +-------------------------------------------------------+ | +-+ |XX J5 | | | |xx Power | | |HDA | | | | |XX 40 Pin | +-+ |XX Task | |XX File | |XX | |XX Inter- | |XX face | SERIAL IN/OUT |XX | LED DRIVE |XX J2 | CAPABILITY |XX |1--2 |XX |+--+ +-+-+-+ | || | J4 +-+-+-+ |XX Power J3 |+--+ E1 DSP C/D |XX +-------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** CONNER CP30064/CP30084/CP30104 PRODUCT MANUAL 00501-045 Jumper setting -------------- Jumpers C/D, DSP, E1 --------------------- C/D - Jumpered addresses drive as drive C. Not jumpered addresses drive as drive D. DSP - Drive slave present. Not jumpered selects single drive only. E1 - Not used. J4 LED DRIVE CAPABILITY ------------------------ 1. 14-Pin Auxiliary Connector +--------------+ |* * * * * * | | * * * * * | +--------------+ Pins 1 & 2 of the SERIAL IN/OUT connector may be used for an ex- ternal LED. 2. 16-Pin Auxiliary Connector +----------------+ |* * * * * * * | | * * * * * * | +----------------+ Pins 3 & 4 of the SERIAL IN/OUT connector may be used for an ex- ternal LED. 3. Separate LED-Connector The newest drive-versions have a separate (white) LED-Connector J3 Power ---------- +---------+ | 1 2 3 4 | +-+-+-+-+-+ | | | +----------- +5V | | +------------- Ground | +--------------- Ground +----------------- +12V J5 Power Connector -------------------- +-------+ | 1 2 3 | +-+-+-+-+ | | +------------- Ground | +--------------- +12V +----------------- + 5V ********************************************************************** I N S T A L L ********************************************************************** CONNER CP30064/CP30084/CP30104 PRODUCT MANUAL 00501-045 Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive may be mounted in any attitude! Recommended Mounting Configuration ---------------------------------- This drive is designed to be used in applications where the units may experience shock and vibrations at greater levels than larger and heavier disk drives. The design features which allow greater shock tolerance are the use of rugged heads and media, a dedicated landing zone, closed loop servo positioning and specially designed motor and actuator assemblies. Ten base mounting points are provided to the customer. The drive is mounted using 6-32 x 1/8" max. insertion for the sides, and 0.20" insertion for the bottom. The system integrator should allow ventilation to the drive to ensure reliable drive operation over the operating temperature range. For additional vibration isolation, an external suspension system may be used. Power Connector --------------- The drives have a 4 pin DC power connector (J4) mounted on the PCB. The recommended mating connector is AMP part number 1-480424-0 utilizing AMP pins, part number 350078-4 or equivalent. DC power may also be supplied to the drive in some interfaces through a 3 pin connector is Molex part number 39-01-0033 utilizing Molex pins, part number 39-00-0031 or equivalent. Task File Interface Connector ----------------------------- A 40 pin Task File Interface connector mounted on the printed circuit board. The recommended mating connector is Molex part number 10-91- 2401 or equivalent. Two drives may be daisy chained together at this connector, and the maximum cable lenght is two feet. Magnetic Field -------------- The disk drive will meet its specified performance while operating in the presense of an externally produced magnetic field under the following conditions. +------------------+------------------+ |Frequency | Field Intensity| +------------------+------------------+ | 0 to 700 Khz | 6 gauss maximum| | 700Khz to 1.5Mhz | 1 gauss maximum| +------------------+------------------+ Acoustic Noise -------------- The sound pressure level will not exceed 40 dBA at a distance of 1 meter from the drive. ********************************************************************** F E A T U R E S ********************************************************************** CONNER CP30064/CP30084/CP30104 PRODUCT MANUAL 00501-045 Key Features ------------ The CP30104 is a high performance 3.5 inch low-profile (1") 121 megabyte (formatted) disk drives with 19 ms average seek time, that is designed to operate on an IBM PC/AT or equivalent in translate mode. The CP30064 and the CP30084 are 60 and 80 megabytes (formatted) versions of the drive. The drives feature low power requirements and high shock resistance, enabling battery operation in portable environments. Because the drive contains the Task File within its control logic, it requires a simplified adapter board to operate. Conner Peripherals has developed an adapter board to be used in conjunction with the drive on an AT or equivalent system. - Low power requirements enabling battery operation in portable environments. - High performance rotary voice coil actuator with embedded servo system. - One of seven run length limited code. - High shock resistance - Sealed HDA - Automatic actuator latch against inner stop upon power-down. - Microprocessor-controlled diagnostics routines that are auto- matically executed at start-up. - Automatic error correction and retries - 512 bytes block size - Emulates Task File with support additional commands. - Up to two drives may be daisy-chained on the AT interface. Translation ----------- The physical parameters of the drive are 1524 cylinder, 4 heads, and 39 sectors. At power up, the CP30104 will default to its translation mode which is 762 cylinders, 8 heads and 39 sectors. At power up, the CP30064 will default to its translation mode which is 762 cylinders, 4 heads and 39 sectors. At power up, the CP30084 will default to 526 cylinders, 8 heads, and 39 sectors. These drives also support uni- versal translate. Split ECC --------- The new generation of Conner drives feature a split sector, that is a 512 byte sector split into two segments. This allows improved error correction performance. The first 254 bytes of the sector are written with their own ECC syndrome which allows for a corrections of any single defect of up to 8 consecutive bits. The second 267 bytes of a sector also have their own ECC syndrome which allows an additional defect correction in the second half of the sector. This allows for 1 ECC correction for each half of a sector or up to two for each sector depending on placement. However some diagnostics expect an uncorrectable error to be report- ed when there are two defects more than 8 bits apart. This will not happen if the defects are in different segments off the sector, and in that case the improved correction capability will correct both errors. On a read long, the drive returns 512 bytes of data plus 7 bytes of ECC. Seek Times ---------- +----------------------------------+--------+ |Track-to-Track msec. | 8 | +----------------------------------+--------+ | Average msec. typ. | < 19 | | Average msec. max. | 35 | +----------------------------------+--------+ |Latency msec. avg. | 8.8 | +----------------------------------+--------+ The timing is measured through the interface with the drive operating at nominal DC input voltages. The timing also assumes that: - BIOS and PC system hardware dependency have been subtracted from timing measurements. - The drive is operated using its translation drive parameters. The average seek time is determined by averaging the seek time for a minimum of 1000 seeks of random length over the surface of the disk. Write Precomp Register ---------------------- (-HOST CS0, address 1 write only) A register previously used to set write precompensation, that is present but is used only for enabling or disabling LOOK AHEAD READ's. Functional Description ---------------------- The drive contains all necessary mechanical and electronic parts to interpret control signals, position the recording heads over the desired track, read and write data, and provide a contaminant free environment for the heads and disks. Read/Write and Control Electronics ---------------------------------- One integrated circuit is mounted within the sealed enclosure in close proximity to the read/write heads. Its function is to provide head selection, read pre-amplification, and write drive circuitry. The read/write heads are supported by a mechanism coupled to the voice coil actuator. The single circuit card provides the remaining microprocessor- controlled electronic functions, which include: - Read/Write Circuitry - Rotary Actuator Control - Interface Control - Spin Speed Control - Dynamic Braking - Power Management At power down or the start of STANDBY MODE the heads are automatic- ally retracted to the inner diameter of the disk and are latched and parked on a landing zone that is off the data tracks. Drive Mechanism --------------- A brushless DC direct drive motor rotates the spindle. The motor/ spindle assembly is balanced to provide minimal mechanical runout to the disks and to reduce vibration of the HDA. A dynamic brake is used to provide a fast stop to the spindle motor and when power is removed, or upon initiation of STANDBY MODE. Air Filtration System --------------------- The head-disk assembly is a sealed enclosure with an integral 0.3 micron filter which maintains a clean environment for the heads and disks. Head Positioning Mechanism -------------------------- The four read/write heads are supported by a mechanism coupled to the voice coil actuator in the CP30084 and the CP30104. Two heads are removed and a counter balancing weight is substituted in the CP30064. Read/Write Heads and Disks -------------------------- Data is recorded on 95mm diameter disk through four miniature metal- in-gap heads. The configuration is one disk and two heads for the CP30064. Error Correction ---------------- The drive performs internal error correction. The error correction polynominal is capable of correcting one error burst with a maximum of 8 bits in each half of a 512 byte block. Reliability and Maintenance --------------------------- MTBF 150,000 hours (base on field return data from this and prior generations of products utilizing similar technology) MTTR 10 minutes typical Preventive Maintenance None Component Design Life 5 years Safety Standard --------------- Conner Peripherals disk drives are designed to comply with relevant prodcut safety standards such as: - UL 478, 5th edition, Standard for Safety of Information Processing and Business Equipment, and UL 1950, Standard for Safety of Information Technology Equipment - CSA 22.2#154, Data Processing Equipment and CSA 22.2#220, Inform- ation Processing and Business Equipment CSA 22.2#950, Safety of Information Technology Equipment - IEC 435 Safety Requirements for Data Processing Equipment, IEC 380, Safety of Electrically Energized Office Machines, and IEC 950, Safety of Information Technology Equipment Including Electrical Business Equipment - VDE 0805 Equivalent to IEC 435, VDE 0805 TIEL 100, Equivalent to IEC 950, and VDE 0806, Equivalent to IEC 380 - TUV Essen und TUV Rheinland Notice ------ Conner Peripherals makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Conner Peripherals shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material.