S D - 3 2 4 0 - 3 0 TEAC NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1930| | | Capacity form/unform 249/ MB Heads 4| | | Seek time / track 17.0/ 7.0 ms Sector/track 62| | | Controller IDE / AT Precompensation Cache/Buffer 64 KB READ-AHEAD Landing Zone Data transfer rate 2.500 MB/S int Bytes/Sector 512 4.000 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 50 | -40 60 Power: sleep 0.1 W Humidity % 8 80 | 8 80 standby 0.5 W Altitude km | idle 3.2 W Shock g 5 | 70 seek 5.1 W Rotation RPM 3600 read/write 3.4 W Acoustic dBA 45 spin-up W ECC Bit MTBF h 100000 Warranty Month Lift/Lock/Park YES Certificates CSA,TUV,UL478 ********************************************************************** J U M P E R S ********************************************************************** TEAC SD-3240-30 HARD DISK DRIVE SPECIFICATION 10530648-01 Jumper Setting ============== Indicator LED ------------- The indicator (LED) on the front bezel lights up while the HDD executes a command. An external LED can also be lighted through the -SLV/ACT signal terminal on the same condition by setting the strap S0 to ON. Straps ------ The setting method for the straps, S2 and S3, should be changed according to the number of the HDDs connected as shown in the following table. Functions of straps +----------+-------------------------------------------------------+ | Strap No.| Function | +----------+-------------------------------------------------------+ | SP | Changes over the function of the -SLV/ACT output | | | signal. | | | ON : The -ACTIVE signal is selected. The external LED| | | can be lighted up at the -SLV/ACT signal | | | terminal. | | | OFF : The -SLAVE PRESENT signal is selected. | +----------+-------------------------------------------------------+ | S0 | (Not used) | +----------+-------------------------------------------------------+ | S1 | Changes over the -I/O CH RDY output signal. | | | OFF : The -I/O CH RDY signal is not output. | | | ON : The -I/O CH RDY signal is output. | +----------+-------------------------------------------------------+ | S2 | Selects the master drive or slave drive. | | | OFF : Only one unit used, or master drive with two | | | units used. | | | ON : Slave drive with two units used. | +----------+-------------------------------------------------------+ | S3 | Selects whether one HDD is used singly, or two HDDs | | | are used in daisy chain connection. | | | ON : Two HDDs are used. | | | OFF : Only one HDD is used. | +----------+-------------------------------------------------------+ Notes: 1. ON : Strap short OFF : Strap open 2. At the shipping of the HDD, the strap SP is set to ON, S0 to OFF, S1 to OFF, S2 to OFF, S3 to OFF. How to set the straps, S2 and S3 -------------------------------- +-------------------------+--------------+-----+-----+ |Number of HDDs connected | Master/Slave | S2 | S3 | +-------------------------+--------------+-----+-----+ | 1 | - | OFF | OFF | +-------------------------+--------------+-----+-----+ | 2 | Master | OFF | ON | | | Slave | ON | ON | +-------------------------+--------------+-----+-----+ ********************************************************************** I N S T A L L ********************************************************************** TEAC SD-3210-00/3240-00/30 Notes on Installation ===================== Drive Orientation ----------------- The head assembly uses a rotary actuator that provides circular arc head motion about the support point. This keeps the drive well- balanced and allows it to be installed in virtually any physical orientation. horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ Screws ------ 3-#6-32UNC 4 deep each side. 4-#6-32UNC 4 deep bottom. Auto shipping lock function --------------------------- The auto shipping lock is designed to protect the media against the risk of damage due to vibration and shock during transport. When the power is turned off, the head carriage is locked automatically at the shipping zone, within the inside limit of the work zone, to protect your important stored data. Automatic self-diagnosis ------------------------ When the power is switched on, the SD-3210 and SD-3240 automatically performs a selfcheck sequence, checking program ROM, buffer RAM, and interface register.