1 9 8 3 7 5 COMPAQ NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | 1011| | Capacity form/unform 342/ MB Heads | 15| | Seek time / track 14.0/ ms Sector/track | 44| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 128 KB Landing Zone Data transfer rate 1.250 MB/S int Bytes/Sector 512 13.000 MB/S ext DMA Recording method RLL operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h 350000 Warranty Month Lift/Lock/Park YES Certificates CSA,TUV,UL1950,VDE ********************************************************************** L A Y O U T ********************************************************************** QUANTUM PRODRIVE LPS 127/170/340 AT UNIVERSAL CONFIGURATION CARD +---------------------------------------------------------+ | JP1+-+-+-+ |XX | +-+-+-+ |XX | SP DS CS |XX | |XX | |XX AT-Bus | |XX | |XX | |XX | |XX | |XX | |XX | | | | +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** QUANTUM PRODRIVE LPS 127/170/340 AT UNIVERSAL CONFIGURATION CARD Jumper setting ============== JP1 Drive Select/Cable Select/Slave Present -------------------------------------------- +------+------+------+--------------------------------------------+ |DS |CS |SP | Description | +------+------+------+--------------------------------------------+ |OPEN |OPEN |OPEN | Slave Drive | | | | | Compatible with drive using PDIAG- line to | | | | | handle Master/Slave communications | +------+------+------+--------------------------------------------+ |OPEN |OPEN |CLOSED| Slave Drive | | | | | The PDIAG- and DASP- lines are not driven | +------+------+------+--------------------------------------------+ |CLOSED|OPEN |OPEN | Master Drive | | | | | Uses DASP- to check for the presence of a | | | | | Slave | +------+------+------+--------------------------------------------+ |CLOSED|OPEN |CLOSED| Master Drive | | | | | Uses the SP jumper to determine whether a | | | | | Slave is present, without checking PDIAG- | | | | | or DASP- | +------+------+------+--------------------------------------------+ |OPEN |CLOSED| X | Slave or Master Drive, depending on the | | | | | state of the Quantum Cable Select signal | | | | | (pin 28) at the IDE-bus interface | | | | | connector. | | | | | If the signal state is set to OPEN | | | | | (grounded) then the drive is configured a | | | | | if DS were CLOSED, described above. If the | | | | | Cable Select signal is set to CLOSED | | | | | (high), then the drive is configured as if | | | | | DS were OPEN, described above. | +------+------+------+--------------------------------------------+ X indicates the jumper setting does not matter. Caution: The CS and DS jumpers should never be installed at the same time. DS Drive Select Jumper ----------------------- You can configure two drives on the ATA Interface as Master (Drive 0) and Slave (Drive 1) using the DS jumpers. Set the CS jumpers to OPEN for each drive. Then, set the DS Jumper to CLOSED on one drive to configure that drive as Master. Set the DS jumper to OPEN on the other drive to configure as Slave. Note: For drives configured using the DS jumper, the order in which drives are connected in a daisy chain has no significance. CS Cable Select Jumper ----------------------- When two ProDrive LPS 127/170/340AT hard disk drives are daisy- chained together, they can be configured as Master and Slave by using the CS jumper or by using the DS jumper - BUT NOT BOTH. To configure the two drives using the CS jumper, set the CS jumper to CLOSED and the DS jumper to OPEN on each drive. Once you install the CS jumper, the drive is configured as a Master or Slave by state of the Cable Select signal, which is pin 28 at the IDE-bus interface connector. Quantum uses pin 28 as a vendor-specific pin; it does NOT conform to the function normally allocated for this pin according to the ATA (AT Attachment). Pin 28 is grounded - that is, set to OPEN - on the cable coming from the host. This configures the first drive as Master. Then, pin 28 on the connector at the second drive should be made an open circuit by a cut in signal line 28 in the cable from the first drive, so it becomes high - that is, set to CLOSED - due to a pull-up in the second drive. This configures the second drive as a Slave. SP Slave Present Jumper ------------------------ The SP jumper normally is not needed. However, when the ProDrive LPS 127/170/340AT is configured as Master and is connected to a Slave drive that does not implement the Drive Active/Slave Present (DASP-) signal, it is necessary to set the SP jumper to CLOSED on the ProDrive LPS 127/170/340AT.