S T 3 2 1 0 5 W C C A Y M A N SEAGATE NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 3892| | | Capacity form/unform 2147/ MB Heads 10| | | Seek time / track 9.0/ 2.0 ms Sector/track | | | Controller SCSI2/3 WI/SCA/FAST Precompensation Cache/Buffer 512 KB ADAPTIVE Landing Zone Data transfer rate 4.000 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep W Humidity % 5 95 | 5 95 standby W Altitude km -0.061 3.048| 12.192 idle 5.9 W Shock g 5 | 75 seek 7.6 W Rotation RPM 5400 read/write 6.8 W Acoustic dBA spin-up W ECC Bit MTBF h 1000000 Warranty Month 60 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** CONNER CFP-2105E PRODUCT MANUAL 501-072 7/94 PRE-RELEASE REV. A +---------------------------------------------------------+ | +-J1 | | | | | | | | |+---+ | | | ||XXX| | +-+ ||XXX| | ||XXX| | ||XXX| | ||XXX| | ||XXX|J2 | J3 ||XXX| | +-+ SS ||XXX| | | | LED ||XXX| | | | ||XXX| | +-+ |+---+ ++ | ++LED | +---------------------------------------------------------+ There are no jumpers to set on the model CFP2105E drive since all the necessary control signals are on the SCA connector. This drive is intended for applications where the drive is configured at the inter- face when drive is plugged into the interface connector. ********************************************************************** J U M P E R S ********************************************************************** CONNER CFP-2105E PRODUCT MANUAL 501-072 7/94 PRE-RELEASE REV. A Setting the SCSI Bus Address ---------------------------- +-------+------+------+------+------+ |SCSI ID|ID0 |ID1 |ID2 |ID3 | +-------+------+------+------+------+ | 0 |OPEN |OPEN |OPEN |OPEN | +-------+------+------+------+------+ | 1 |GROUND|OPEN |OPEN |OPEN | +-------+------+------+------+------+ | 2 |OPEN |GROUND|OPEN |OPEN | +-------+------+------+------+------+ | 3 |GROUND|GROUND|OPEN |OPEN | +-------+------+------+------+------+ | 4 |OPEN |OPEN |GROUND|OPEN | +-------+------+------+------+------+ | 5 |GROUND|OPEN |GROUND|OPEN | +-------+------+------+------+------+ | 6 |OPEN |GROUND|GROUND|OPEN | +-------+------+------+------+------+ | 7 |GROUND|GROUND|GROUND|OPEN | +-------+------+------+------+------+ | 8 |OPEN |OPEN |OPEN |GROUND| +-------+------+------+------+------+ | 9 |GROUND|OPEN |OPEN |GROUND| +-------+------+------+------+------+ | 10 |OPEN |GROUND|OPEN |GROUND| +-------+------+------+------+------+ | 11 |GROUND|GROUND|OPEN |GROUND| +-------+------+------+------+------+ | 12 |OPEN |OPEN |GROUND|GROUND| +-------+------+------+------+------+ | 13 |GROUND|OPEN |GROUND|GROUND| +-------+------+------+------+------+ | 14 |OPEN |GROUND|GROUND|GROUND| +-------+------+------+------+------+ | 15 |GROUND|GROUND|GROUND|GROUND| +-------+------+------+------+------+ Disabling Spin-Up at Power On ----------------------------- Spin up upon application of power to the drive can be diasabled by grounding the RMT_START line on the interface. Disabling spin up on application of power can also be enabled by setting the DSPN bit in MODE SELECT page 00H (Operating Parameters). The Host must issue a START UNIT command to cause the drive to spin up. RMT_START |DSPN |Result ----------+-----+------------------- Ground | 0 |Spin Disabled Ground | 1 |Spin Disabled Open | 0 |Spin Up on Power On Open | 1 |Spin Disabled Delaying Spin Up at Power On ---------------------------- Grounding the DLYD_START signal on the interface delays spin up on power-up by the value of the drive's SCSI ID multiplied by 4 seconds. Delaying spin up on application of power can also be enabled by setting the SDLY bit in MODE SELECT page 00H (Operating Parameters). DLYD_START|SDLY |Result ----------+-----+------------------- Ground | 0 |Spin Delayed Ground | 1 |Spin Delayed Open | 0 |Spin up on Power On Open | 1 |Spin Delayed ********************************************************************** I N S T A L L ********************************************************************** CONNER CFP-2105E PRODUCT MANUAL 501-072 PRE-RELEASE REV. A 7/1994 Notes on Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Mounting the Drive ------------------ The drive is designed to be used in applications where the unit may experience shock and vibrations at greater levels than larger and heavier disk drives will tolerate. The design features which allow greater shock tolerance are the use of rugged heads and media, a dedicated landing zone, closed loop servo positioning and specially designed motor and actuator assemblies. Eight side, or four bottom base mounting points are provided to the customer. The drive is mounted using 6-32 UNC -2B X 0.16 maximum insertion length screws. The system integrator should allow ventilation to the drive to ensure reliable drive operation over the operating temperature range. The drive may be mounted in any orientation. Cabling the Drive ----------------- The drive is intended for direct backplane connection to the SCA connector rather than through cabling. Attaching Power to the Drive ---------------------------- The drive is powered through the SCA connector and is intended for direct backplane connection rather than through cabling. External Terminator Power ------------------------- The interface connector carries both power and ground so a separate TERMPWR interface line is not provided. Internal Termination -------------------- This version of the drive has no on-board termination so the drive must be externally terminated. Alternative 2 active termination is recommended. Alternative 1 passive termination is not suitable for this application. Cable Requirements ------------------ This version of the drive is designed to interface directly a mating connector which is on a passive back plane or directly into a motherboard. The same guidelines relative to impedance, stub length and distance between stubs apply for SCSI bus signal reliability. These guidelines may not be directly translated to a back plane design so these design rules are to eb viewed with respect to the intended purpose of controlling reflections and the propagation of signals down the bus. Since the characteristics for PCB signal traces are affected by trace width, proximity to ground, and trace routing, careful review of the back plane design and analysis of signal quality is highly recommended. Connector Requirements ---------------------- The drive's connector will mate with a AMP Champ 2-557103-2 vertical receptacle or the AMP Champ 2-557101-1 right angle receptacle. Single Connector Attachment (SCA) Signal Definitions ---------------------------------------------------- Power Four +12 Volt signals provide the +12 volt power to the drive. The current return for the +12 volt power is through the +12 Volt Ground signals. The maximum current that can be provided to the drive through the +12 Volt signal pins is 3 Amperes. The supply current and return current must be distributed as evenly as possible among the pins. The maximum current is while the drive motor is starting. Three +5 Volt signal pins provide +5 volt power to the drive. The current return for the +5 volt power is through the +5 Volt Ground pins. It is expected that the +5 Volt Ground will also establish the digital logic ground for the drive. The maximum current that can be provided to the drive through the +5 Volt signal pins is 2 Amperes. The supply current and return current must be distributed as evenly as possible among the pins. Spindle Sync ------------ The spindle rotation of up to 35 drives may be synchronized together by daisy chaining pin 1 to pin 1 and pin 2 to pin 2 of each drive on connector J3. The spindles are synchronized using a "floating master" concept, where the drives will synchronize to the first drive to reach full speed. The synchronization tolerance is 1%. LED Out ------- The LED out signal is driven by the drive when the drive is perform- ing a SCSI operation. The LED out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +5 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive. ********************************************************************** F E A T U R E S ********************************************************************** CONNER CFP-2105 PRODUCT MANUAL 501-072 PRE-RELEASE REV. A, JULY 199 Overview of the Drives ---------------------- The CFP2105 series is a family of high performance 3.5-inch low- profile (1.0 inch high) 2.1GB (formatted) disk drives. They all offer 8.5 millisecond average seek time for Reading, 9.0 millisecond seek time for Writing, with an average latency of only 4.17ms. High capacity is achieved by utilizing a zone density recording technique using 15 recording zones at an areal density of 317 Mbits per square inch. These drives feature high performance while maintaining low power consumption to reduce power supply current and system cooling requirements in disk arrays. They are designed to operate on the Small Computer System Interface (SCSI) and are SCSI-2/3 command compatible. The mechanical and major electronic components are identical between the models and differ only in the host interface implementation. Firmware -------- The drive's firmware can be considered in two parts. The first part principally reside in the ROM for the 68HC16 background processor. This processor is responsible for: - starting the spindle motor and maintaining precise rotational speed - controlling track following and actuator motion during seeking - managing background R/W activity - power management - monitoring the overall health of the drive. The interface processor's control microcode resides in both ROM and RAM. The RAM portion of the microcode can be upgraded in the field with using software. The interface processor firmware functions include: - reporting drive status and error conditions to the host - manage operating parameters for the drive - parsing the Command Descriptor Block and checking for illegal fields - converting the LBA to CHS and initiating read and write operations to the background processor - defect management - serial port communications Since parsing/decoding of commands and execution of the Read/Write functions are handled by separate processors, command execution can be overlapped in multiple initiator or Tagged Command Queuing environments. Functions such as seek re-ordering and command coalesc- ing can also be overlapped when the drive is operating with a host environment capable of supporting Tagged Command Queuing. Seek Time --------- +----------------------------------+--------+ | | 2105 | +----------------------------------+--------+ |Track-to-Track msec. typ. | 2 | +----------------------------------+--------+ |Average msec. read | 8.5 | | msec. write| 8.5 | +----------------------------------+--------+ |Full Track msec. | 18 | +----------------------------------+--------+ |Latency msec. avg. | 4.17 | +----------------------------------+--------+ Error Correction ---------------- The drive uses a three way interleaved 144-bit Reed-Solomon code to perform error correction, plus a 6 bit CRC. For each 512-byte block, the on-the-fly error correction polynominal is capable of correcting: - one error burst of up to 41 bits in length - two error bursts each up to 17 bits in length The miscorrection probability is less than 1 bit in 10(24) bits transfered. ********************************************************************** G E N E R A L ********************************************************************** SEAGATE SUPPORT SERVICES Seagate Technology ------------------ Technical Support Services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate(r) drive or other Seagate products, use one of the Seagate technical support services listed below. SeaFONE at 1-800-SEAGATE (1-800-732-4283) Seagate's 800 number allows toll-free access to automated self-help services, providing answers to commonly asked questions, troubleshooting tips and specifications for disc drives and tape drives. This service is available 24 hours daily and requires a touch-tone phone. If you need to speak to a technical support engineer, dial this number and listen to the options for technical support. (International callers can also reach this automated self-help service by dialing 408-456-4496). Seagate Technology online services Using a modem, you can obtain troubleshooting tips, free utility programs, drive specifications and jumper settings for Seagate's entire product line. You can also download software for installing and analyzing your drive. SeaNET You can obtain technical information on Seagate drives, Seagate software and much more over the Internet from Seagate's World Wide Web home page (http://www.seagate.com) or Seagate's ftp server (ftp://ftp.seagate.com). You may also send E-mail with your questions to DiscSupport@ Seagate.com or TapeSupport@Seagate.com. SeaBOARD SeaBOARD is a computer bulletin board system (BBS) that contains information about Seagate's disc and tape drive products and is available 24 hours daily. Set your communications software to eight data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers are listed in the following table. BBS Location Modem number United States Disc: 408-434-1080; Tape: 408-456-4415 England 44-1628-478011 France 33 1-48 25 35 95 Germany 49-89-140-9331 Singapore 65-292-6973 Thailand 662-531-8111 Australia 61-2-9756-2359 Taiwan 886-2-719-6075 Seagate CompuServe forum Online technical support for Seagate products is available on CompuServe. To access our technical support forum, type go seagate. This forum provides information similar to that found on SeaBOARD. In addition, you can type questions or browse through previous questions and answers on the forum messages. Seagate Technology FAX services SeaFAX You can use a touch-tone telephone to access Seagate's automated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Location Telephone number United States 1-800-SEAGATE or 408-456-4496 England 44-1628-894084 Australia 61-2-9756-5170 Seagate technical support FAX You can FAX questions or comments to technical support specialists 24 hours daily. Responses are sent during business hours. Location FAX number United States 408-944-9120 England 44-1628-890660 France 33 1-46 04 42 50 Germany 49-89-1430-5100 Australia 61-2-9725-4052 Singapore 65-293-4722 Hong Kong 852-2368 7173 Taiwan 886-2-715-2923 Korea 82-2-556-7294/4251 Seagate technical support You can talk to a technical support specialist during business hours Monday through Friday for one-on-one technical help. Before calling, note your system configuration and drive model number (STxxxx). There are several technical support phone numbers available for various Seagate products. Location Telephone number United States Please dial 1-800-SEAGATE for the specific product telephone number. (6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M., Pacific time, M-F) England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) France 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 5:00 P.M., M-F) Germany Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 4:00 P.M., M-F) Tape: 49-89-140-9333 Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F) Singapore 65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) Hong Kong 852-2368 9918 Taiwan 886-2-514-2237 Korea 82-2-556-8241 SeaTDD 408-944-9121 Using a telecommunications device for the deaf (TDD), you can send questions or comments 24 hours daily and exchange messages with a technical support specialist between 6:00 A.M. to 11:15 A.M. and 12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday. Customer Service Centers Seagate direct OEM, Distribution, System Integrator and Retail customers should contact your Seagate Service Representative for warranty information. Other customers contact your place of purchase. Seagate offers comprehensive customer support for all Seagate drives. Seagate customer service centers are the only facilities authorized to service Seagate drives. These services are available worldwide. Location Telephone number FAX number United States 1-800-468-3472; 405-949-6740 Other Americas (Canada & Brazil) 405-949-6706; 405-949-6738 Mexico 525-546-6965; 525-546-4888 Europe, Middle East & Africa 31-2065-43300; 31-2065-34320 Asia Pacific & Australia 65-485-3595; 65-485-4980 Japan 81-3-5462-2904; 81-3-3462-2979 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD, SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or registered trademarks of Seagate Technology, Inc. or one of its subsidiaries. All other trademarks or registered trademarks are the property of their respective owners.