S T 3 1 0 5 1 N H A W K 2 X L SEAGATE NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 4569| | | Capacity form/unform 1050/ MB Heads 4| | | Seek time / track 10.0/ 1.0 ms Sector/track | | | Controller SCSI3 SI/FA Precompensation Cache/Buffer 256 KB MULTI-SEGMEN Landing Zone Data transfer rate 5.000 MB/S int Bytes/Sector 512 10.000 MB/S ext Recording method RLL 0/4/4 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 70 Power: sleep W Humidity % | standby W Altitude km | idle 6.3 W Shock g | seek W Rotation RPM 5400 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 800000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** J U M P E R S ********************************************************************** SEAGATE ST31051N HAWK 2XL QUICK REFERENCE GUIDE Jumper Setting ============== REAR VIEW 50 pin I/O Cable Connection | J1+------------------------1+ /---------\ TOP (HDA) -+:::::::::::::::::::::::::+-| 0 0 0 0 |-- +-------------------------+ +-5-G-G-12+ BOTTOM RIGHT SIDE VIEW BACK +-+ J2 12345678 TOP (HDA) FRONT OF J1+---------------------P-W-A----------------------- OF DRIVE +-+ :::::::: BOTTOM DRIVE |||||||| |Terminator Power +||||||+ Enable T-Res ++Terminator Power -+||||+- Start Delay (12 secs * ID) | RESERVED --+||+-- Motor Start | Parity Disable ---++--- Write Protect | | | +----------------------------------------------+ +-+ Termination Power-source Table | +----------------------------------------------+ |-----....-----....-----PWA edge----- | | | | 1 2 1 2 1 2 | | A Drive Supplies Bus | | X * * X xxx B Drive Supplies Own | | x * * x * * C Bus Supplies Drive | | A B C | +---------Default------------------------------+ FRONT VIEW +--+RESERCED! Shipped with cover installed. | +Do not remove! Do not install jumpers TOP (HDA) ++---+ 1 --P-W-A----------------+::::|::::::+-- * BOTTOM +----+123456 | J6 |||||| LED -+ |||||| Remote LED +||||+ ID 1 (pin-11 +5V) |||+- ID 2 RESERVED -+++-- ID 4 SCSI ID ------- +----------+-----------------------+ | SCSI ID | Jumpers | | | ID4 | ID2 | ID1 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ ********************************************************************** I N S T A L L ********************************************************************** SEAGATE ST32151/31051N/W/WC INSTALLATION GUIDE Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Things you may need to install the drive ---------------------------------------- - Adequate power from your computer power supply This drive requires 7.5 watts during typical operation, and 6.0 watts when at idle (not reading, writing or seeking). If this drive is an "add-on" make sure the computer power supply can supply enough extra power for this drive's needs. - An antistatic wrist strap You will need this to reduce the possibility of damaging your drive by static discharge. - A #2Phillips screwdriver You will need this screwdriver to open your computer and to insert the drive mounting screws. - A Torx Size TX-08 driver tool If your drive has a front panel and you need to install the drive in a conversion frame kit, this tool will be needed. - A bootable DOS system diskette for the PC You will need this diskette, which should contain the DOS system files and the programs FDISK.EXE and FORMAT.EXE to partition and format your new hard drive. - A SCSI host adapter card for the PC You may need this if your computer does not already have a hard drive, if your present drive does not connect to a SCSI host adapter, or if your present SCSI adapter card cannot address a drive having the capacity the Hawk 2XL has. The host adapter card should have instructions with it for installing the card and assist in the installation of hard disc drives that it supports. - A 50-pin SCSI interface cable You will need an interface cable if your computer does not presently contain a SCSI hard drive. If you are adding a second hard drive you must use an interface cable that has two drive connectors, one on the end and one in the middle. - A Y-shaped drive power cable You may need this if your computer does not have enough power cables to supply power to your new hard drive. - Mounting screws You will need four 6-32 x 1/4 inch (6.4 mm) nonmetric screws if you mount your drive directly into the drive bay. - Drive mounting rails You may need drive rails if your computer's drive bay is not designed for direct mounting. - A frame kit You will need a frame kit if you wish to mount a 3.5-inch disc drive in a 5.25-inch drive bay. - Extra configuration jumpers A small plastic bag of two types of configuration jumpers is included in drive package. Mounting the drive ------------------ Important Precautions: - Make sure your computer is turned off before beginning installation. - Although switched off, your computer must remain plugged into an electrical outlet with an earth ground. This minimizes the possibility of damage from static discharge. - Static electrical charges can accumulate quickly on people, clothing and synthetic materials. The electrostatic fields due to these charges when brought in close proximity to susceptible circuit assemblies and components, can result in degraded reliability or immediate failure of the affected component or assembly. - Always wear a grounded wrist strap. Attach the wrist strap to the metal chassis of your computer. Use the antistatic pad as your work surface, and avoid installation in areas with static-inducing carpets. 1. Begin by removing the cover of the computer. Follow the instructions in your computer manual. Systems that use "WC" drives probably do not require cover removal, as the drives are mounted in a module that slides into place and plugs in. 2. Does your system have 5.25-inch drive bays? Your Seagate drive is designed to fit into a 3.5-inch wide drive bay. If your computer has 5.25-inch drive bays, then you must mount the drive ("N" or "W" models only) in a conversion frame kit before it will fit into your com-puter. Purchase a conversion frame kit from your com-puter dealer if necessary. 3. Connect the 50 or 68 pin interface cable to the hard drive interface connector on the SCSI host adapter card. Be careful not to bend the pins on the host adapter card connector. Refer to your SCSI host adapter manual for the location of the interface connector. The sockets on the interface cable must be matched correctly with the pins on your SCSI host adapter interface connector. Verify the location of pin 1 on the SCSI host adapter using your computer system's manual. Pin 1 on the interface cable is indicated by the stripe along the edge of the cable. Plug the cable into the hard drive interface connector on your SCSI host adapter. 4. Thread the other end of the interface cable through your drive bay and connect to the disc drive. The sockets on the interface cable must be matched correctly with the pins on the disc drive. Pin 1 on the interface cable is indicated by the strip along the edge of the cable; pin 1 on the Seagate disc drive is the pin closest to the HDA, on the side closest to the four-pin power supply connector. Plug the interface cable into the drive connector firmly but carefully. The connector should cover both rows of pins. If you are installing a second or multiple disc drives, repeat this procedure using the additional drive connectors on the interface cable. 5. Mount the drive in a drive bay. - Direct mounting: The disc drive can be mounted in the drive bay in any orientation permitted by the drive bay mechanical configuration. Be careful not to over tighten the mounting screws. Screws must not extend into the side drive mounting holes more than 0.015 inches, (9/64 inches) or into the bottom mounting holes 0.20 inches (3/16 inches). Purchase the four required 6-32 x 1/4 inch screws at a hardware or drive supplier store. - Using drive rails: In some computers, you must attach drive rails to either side of the drive, then slide the drive into the drive bay on its drive rails. Be sure that the drive is securely mounted within the bay. In computers that do not use drive rails, screw the drive or the frame kit holding the drive directly to the drive bay. - Using a conversion frame kit: To mount a 3.5" drive in a 5.25" drive bay, install the drive in the frame kit (installation instructions and required hardware are included with a frame kit). Then mount the frame kit in the drive bay. If you are installing two disc drives, repeat the appropriate procedure above for the second drive. - Using a special module: "WC" drives should be fitted with slides or most likely, mounted in a special module that slides into the host equipment. - Drive activity LED: If the drive mounts such that the drive activity LED does not show when the computer cover is on, the computer may provide for a remote LED two conductor cable to be used on all models. This cable plugs into J6 on the front of the drive. "WC" model drives have a line available in the J1-80 pin interface. Check system documentation to see if J1 signal is used or if a cable should be attached to J6. 6. Attach a system power cable to the power connector on each drive. If your system does not have an extra power cable for the hard drive, you can purchase a Y-shaped power cable, such as the one. 7. Review each of the previous steps to verify that you have completed the installation correctly. 8. Replace the cover on your computer. ********************************************************************** F E A T U R E S ********************************************************************** SEAGATE ST32151/31051N/W/WC INSTALLATION GUIDE Before you begin ---------------- Verify that the system is switched off but remains connected to the main power before any installation is attempted. Protect yourself, the drive, and your valuable programs and data by reading the following cautions and warnings. - Do not tamper with sealed top cover. Doing so voids your warranty. The drive contains no user serviceable compo-nents. See Product Repair section for more information. - Visually inspect the shipping container for any obvious damage. - Verify all parts listed on shipping bill are received with the equipment. Discrepancies or damage should be reported to the shipping company. - Inspect drive for possible shipping damage. All claims of this type should be filed promptly with the transporter involved. Save original packing materials to be used when reshipping. - When transporting or shipping a drive or system, please ensure that they are correctly packed in original Seagate approved (or equivalent) container and shipped via an airride carrier experienced in handling computer equipment. - Do not unpack drive from its static shielded bag until you are ready to install it in the system. - Always handle the drive by the frame or casting. - Do not touch Printed Circuit Board (PCB) or the I/O connector pins. - Never apply pressure to the PCB or to the drive top cover. Configuring the computer for your drive --------------------------------------- The hardware part of your installation should now be complete. Software installation informs your computer operating software about your Seagate disc drive characteristics. You can then divide your drive into partitions called "logical drives." DOS Installation ---------------- To install your Seagate disc drive in your computer software, your computer operating system should be Microsoft DOS version 4.0 or higher. Your SCSI adapter card must be able to address greater than two gigabytes. If you already have a hard disc drive on your computer and you are installing a second drive, now is a good time to evaluate the status and quality of your backups. Once you are satisfied with the status of your backups, then proceed. Caution. Determine which drive is to be partitioned in a two drive system. - Turn your computer on and boot-up from your existing hard drive or from a diskette in drive A, whichever is applicable. Watch the screen for text that tells which key(s) to press to branch into the system setup program. Hit CTL-ALT-DEL to boot-up again if you missed it. Choose to go into setup. - Setup presents a menu. Choose the menu item that asks you to declare the drive type. If the screen says the drive type is "not installed" or something similar, save that and leave setup. If it asks you to enter a drive type, enter "none," "drive not installed," "type 0" or whatever similar response is given as a choice on the menu. - Save and leave this screen. The computer will probably boot up again. If not, hit CTL-ALT-DEL. - At the C> prompt or A> prompt, run the FDISK utility program either from your existing hard drive or from a diskette in drive A. (refer to your DOS user's Reference Manual for more detailed instructions on FDISK procedures). - A menu comes up that gives choices pertaining to installing your new drive and dividing it into partitions. If the drive you set the jumpers for is Drive ID 0 (no ID jumpers on), the menu will stay at the top, "Current fixed disk drive: 1" - From the menu choose "Create a DOS partition..." - Proceed to set up desired partitions. - If your new drive is jumpered as Drive ID 1, choose "Select next fixed disk drive" on the menu. FDISK displays the main menu again, but at the top it says "Current fixed disk drive: 2". - The menu displayed gives you the same opportunity as mentioned above to partition your second drive as several logical (simulated) drive volumes. Caution. Do not try to change the partitions set up for an existing inuse drive. If you change any partitions or logical (simulated) drive assignments on your existing drive, you will lose all data stored. Always backup the existing drive's data on diskettes, tape, or other media before changing the drive's configuration. The first hard drive (drive jumpered as ID 0) is always called drive C. If you already have a hard drive, FDISK shows it as drive C and shows if it has been divided into a primary DOS partition and an extended partition. The extended partition can be divided into several logical drives. FDISK lists these logical drives as D, E, F, etc. The primary DOS partition has the operating system on it (this is the start up or "Boot-up" partition). From the main menu, choose to set "Active" the DOS partition you want to boot from, which is the primary DOS partition. Many people like to make drive C a few megabytes, devoted almost entirely to the operating system (DOS or other) and little else. They put other programs on other logical drives, grouped in categories that provide a distribution of data and programs across all logical drives that suits their applications. When satisfied with the set up as instructed in the menus presented, reboot the drive. Formatting ---------- Caution. Do not format the existing drive that contains user data that you don't want to lose, as all user data will be lost when a drive is formatted. When a second drive is installed, the drive letters assigned by DOS to the first drive may change. Be careful not to accidently format a logical drive with existing data. When you complete drive partitioning, you need to high-level format every new logical drive you have set up. If your new drive is to be the boot-up drive, insert the DOS system diskette in drive A and type at the A/> prompt FORMAT C: / s/v. This formats drive C and puts the programs on that are necessary to boot the computer from the C drive, and verifies that the format was performed correctly. For each additional logical drive you have changed or newly set up, type in FORMAT X: /v (where "X" is the proper drive letter for the drive to be formatted). Note: Seagate Technology assumes no liability for lost user data. From the C/> prompt, try to switch to each logical drive (C:, D:, E:, etc.) to see if you can get a prompt for each logical drive (C\>, D\>, E\>, etc.). With each prompt that you select, type CHKDSK. This shows if the logical drives are usable for storing data and programs. If the logical drives you set up are not recognized, try the FDISK set up routine and FORMAT again. You may have made a small mistake at some point in the installation procedure. Make sure that the total capacity shown for your new drive is equal (or close to) the formatted capacity given in the Product Information table, column B at the end of this guide. If not, you may need to get a newer SCSI adapter card that allows you to access the complete drive. If the complete DOS operating system software is not on your primary DOS drive (usually C), read it in from diskettes on drive A. Macintosh installation ---------------------- To configure this drive in a Macintosh system, you must use a third-party hard disc initialization application. Most software vendors and computer stores that carry Macintosh software will have hard disc drivers available for purchase. Follow the instructions provided with the disc initialization application to complete the installation of your Seagate drive. Note. The Apple HD SC Setup utility included with your Macintosh system software only works on drives or-dered directly through Apple. Unix installation ----------------- There are several versions of the Unix operating system. Each of these handle hard disc installation in a different manner. For this reason, refer to your system's operation manual for information about how to complete the installation of this disc drive. Contact Seagate Technical support services for any additional information needed to install the drive in a Unix system. ********************************************************************** G E N E R A L ********************************************************************** SEAGATE ST32151/31051N/W/WC INSTALLATION GUIDE Troubleshooting --------------- Before calling Seagate Technical Support, please read and consider the possibilities discussed below. The suggestions presented here will resolve the majority of installation problems. General installation troubleshooting ------------------------------------ - Check system compatibility. This is a SCSI interface device. Check your system documentation to ensure that is supports SCSI interface devices. - Check the drive ID assigned. Model "N" has three drive ID jumper positions on the drive. - Check the drive operating feature jumpers. - Check to ensure that drive is receiving power. Insert the drive into your system. Listen carefully for the sound of the drive motor spinning up. There should be the rotational spin up noise, with no interruption, followed by seeking noises and clicks. If the drive motor does not spin up, check the power supply. If your power supply is functioning properly, but the drive does not spin up, contact the company from which you purchased the drive. If you have added one or more drives to your existing system the power supply may not be able to furnish enough power. Check with your drive purchase source about this. Inadequate power supplies may work for a short period of time under great stress, and then either fail or operate in a severely degraded mode. It may supply enough +5 V for the logic to respond, but not enough current on the +12 V for a spinup.