M 3 4 3 8 P L U S MINISCRIBE NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/HH Cylinders 615| | | Capacity form/unform 32/ 38 MB Heads 4| | | Seek time / track 55.0/15.0 ms Sector/track 26| | | Controller RLL / ST412 Precompensation 128 Cache/Buffer KB Landing Zone Data transfer rate 0.938 MB/S int Bytes/Sector 512 0.938 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 4 50 | Power: sleep W Humidity % | standby W Altitude km | idle 18.6 W Shock g | seek W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 20000 Warranty Month Lift/Lock/Park NO Certificates ********************************************************************** L A Y O U T ********************************************************************** MINISC. 3425P/3438P/3650/3675 PRODUCT DESCRIPTION +-------------------------------------------------------+ | |XX Power | |XX | | | |XX | |XX Control | |XX Cable | |XX J1 | |XX | |XX | |XX | DS0+-+ | | DS1| | |XX | DS2| | |XX | DS3| | |XX | JP3| | |XX Data | +RP1------+ JP2| | |XX Cable | +---------+ JP1+-+ |XX J2 +-------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** MINISC. 3425P/3438P/3650/3675 PRODUCT DESCRIPTION Jumper Setting ============== Drive Select ------------ +-----------------+---------+-------+-------+-------+ | | DS0 | DS1 | DS2 | DS3 | +-----------------+---------+-------+-------+-------+ |Drive Select 0 | CLOSED | OPEN | OPEN | OPEN | +-----------------+---------+-------+-------+-------+ |Drive Select 1 | OPEN | CLOSED| OPEN | OPEN | +-----------------+---------+-------+-------+-------+ |Drive Select 2 | OPEN | OPEN | CLOSED| OPEN | +-----------------+---------+-------+-------+-------+ |Drive Select 3 | OPEN | OPEN | OPEN | CLOSED| +-----------------+---------+-------+-------+-------+ Drive Cabling ------------- If you are connecting the drive with a straight (non-twisted) 34 pin control cable, verify that the drive select jumper is on DS0. If you are using a twisted 34 pin control cable (5 wire twist), move the drive select jumper to DS1. Verify that both the 20 pin data cable and the 34 pin control cable are connected to pin 1 at the drive connectors and pin 1 of the controller board connector. Note: The colored edge of both ribbon cables represents pin 1. If the drive will be the secondary device of a two-drive setup re- move terminating resistor RP1. ********************************************************************** F E A T U R E S ********************************************************************** MINISC. 3425P/3438P/3650/3675 PRODUCT DESCRIPTION Formatting Guidelines --------------------- Before a hard disk drive can be used, 3 steps must be completed: 1. The drive must be low-level formatted to establish communications with the disk drive and controller board. 2. The drive must be partitioned into one or more logical drives. Use the fdisk programm from DOS versions 3.3 or higher or partioning software like Disk Manager or Speedstor. 3. The drive must be high-level formatted to prepare it for the operating system installation. Use the DOS format command or Disk Manager/Speedstor software. XT 8086/8088 Installation ------------------------- Use the utilities from any 8 bit controller board to low-lwvel format the drive. Typical routinetis to use the DOS debug command to address these utilities. If the low-level format program of the controller asks for step pulse rate or control byte values, use the controller default values. AT 80286/80386 Installation --------------------------- Use the MiniScribe version of Ontrack Disk Manager software or the Universal version of Speedstor software of the entire formatting process.